PS3Hax Network - Playstation 3 and Playstation 4 Hacks and Mods - PS3 | Downgrading and Flashing http://www.ps3hax.net/ Discussion of downgrading/flashing/unbricking the PS3 including support of ProgSkeet and other clones/alternatives en Thu, 23 Oct 2014 04:34:49 GMT vBulletin 60 http://www.ps3hax.net/PS3HAX/images/misc/rss.png PS3Hax Network - Playstation 3 and Playstation 4 Hacks and Mods - PS3 | Downgrading and Flashing http://www.ps3hax.net/ Where can I find service? liverpool. http://www.ps3hax.net/showthread.php?t=78684&goto=newpost Thu, 23 Oct 2014 01:17:03 GMT
I'm looking for someone to convert my 4.55 cex cfw console to dex.
I've watched countless tutorials but I am too scared of bricking my console, so I would like someone to do it for me.
If you're able to do it and live near L6 (Anfield) please message me with a quote.
Thank you.
]]>
PS3 | Downgrading and Flashing AlterProof http://www.ps3hax.net/showthread.php?t=78684
8002F147 error http://www.ps3hax.net/showthread.php?t=78662&goto=newpost Wed, 22 Oct 2014 08:25:42 GMT hi guys i have a ps3 slim 2003 Model it was giving me a 8002F157 data is corrupted when i try to update so i tried to downgrade the console to get...
hi guys i have a ps3 slim 2003 Model it was giving me a 8002F157 data is corrupted when i try to update so i tried to downgrade the console to get rid of this Error Code i used FSM method i have e3 card reader that worked on every PS3 i did over 100 console i patched the e3 downgrade file and switched off the ps3 to use the Dongle but i couldn't enter to FSM the dongle keeps on Blue Light and the console keeps asking for 3.70 FW or later again i've tried Rogero 4.55 , Habib 4.60 , OFW 4.50-4.65 nothing work all of them gives me the same error (8002F157) but the only one that worked is the 3.55 rogero Downgrader the console start updating and bypassed the previous error code but now on 27% i get new error (8002F147) and as i know this error is Bad BD-Drive or the BD not connected i have connected the BD and nothing changed the update stops on 27% i tried different HDD ,USB same thing i formatted the HDD and the PS3 back to request 3.70 AGAIN i inserted Original FIFA 14 Disc to check if my BD is damaged or not and the PS3 accepted the update on the Disc and start preparing for update after finish i get the same old error ( The Data Is Corrupted 8002F157) i searched in the forums for this error code but i couldn't find a clear answer

so is there anything else i can do for this strange issue !
]]>
PS3 | Downgrading and Flashing unkn0wn.92 http://www.ps3hax.net/showthread.php?t=78662
the noobs downgrading the right way http://www.ps3hax.net/showthread.php?t=78646&goto=newpost Tue, 21 Oct 2014 21:58:53 GMT http://www.ps3hax.net/showthread.php?t=33989 as been told many times on the forum use playerkp420s guide you cant go wrong with it
http://www.ps3hax.net/showthread.php?t=33989 as been told many times on the forum use playerkp420s guide you cant go wrong with it
]]>
PS3 | Downgrading and Flashing pauline45 http://www.ps3hax.net/showthread.php?t=78646
PLEASE HELP :( http://www.ps3hax.net/showthread.php?t=78625&goto=newpost Tue, 21 Oct 2014 03:48:33 GMT
Okay, so I'm trying to jailbreak a good friend's PS3. He is absolutely clueless as to what I'm doing. He doesn't understand any of it. So I took it apart, got 3 valid backups (which I still have) & patched it. I then flashed the patched backup and all was good. Once it turned on, I installed the Rogero 999 downgrade firmware. I installed the Toggle QA pkg and ran it but I never got the 3 beeps. I just decided that the QA wasn't important because all he wants is a custom firmware that he can use to play on psn and back up games so he wouldn't be changing firmware very often. Anyway, when I tried to install 3.55 OFW it said it was corrupt. When I rebooted, it took me to a screen that told me that the firmware could not start correctly. I tried installing OFW again with the same result. Then I tried to reinstall the downgrade firmware and it would get stuck at 98%. I then flashed the original, unpatched nor backup. Now the PS3 will turn on for about 2-3 seconds, beep 3 times, and stop. Does anybody have any kind of solution to fix this, or at least get it back to 4.65 ofw, where I started.
]]>
PS3 | Downgrading and Flashing CallMeJuni0r http://www.ps3hax.net/showthread.php?t=78625
I will game share a hacked account for pvz garden warfare http://www.ps3hax.net/showthread.php?t=78623&goto=newpost Mon, 20 Oct 2014 23:10:42 GMT
PS3Hax don't support Online Hacks or anything related to that.
]]>
PS3 | Downgrading and Flashing bloodbullett5656 http://www.ps3hax.net/showthread.php?t=78623
<![CDATA[PS3 SLIM 2K - Can't Install nothing on HDD (or others HDD's) - 8002F281]]> http://www.ps3hax.net/showthread.php?t=78622&goto=newpost Mon, 20 Oct 2014 22:46:43 GMT
Hi everyone!! Need a bit of help or some points so i can bypass this (or not). (sorry if i'm posting in wrong section)

So, i got a "free broken ps3" last year with some issue on usb (no power) but i didn't had time to fix it, so i forgot about it. This last week look at it, and with some time i start working on it.

So, just to begin, it hasn't got any HDD. Without USB power i couldnt install it. I notice that a fuse and a resistor and other part were damaged so i trade them from a donnor board, and got back power on usb now. Went and downgraded it to 3.55. When i enter FSM (with the files on the USB) it don't install nothing, notice the usb working, hdd starts everything ok but no luck installing in that HDD.
When i get out of FSM and try to install 4.50 OFW on the HDD it gaves me the error 8002F281 and it the message "a serious error occured contact assistance...error...". The dump is now patched for 3.55.
Tonight wil try and put the original dump and see if i can install an hdd then dump again and flash the noFSM or 3.55 one.

This error can be cause it hasn't got an hdd? or other thing? Or do i need to install a hdd before downgrading or patching for noFSM (in the past never had problems cause i always installed the hdd before to test the ps3 or something, but this one i did the reverse - went straight to 3.55 without any hdd or ofw firmware on a hdd installed before...).

I can go to FSM, can get out FSM, but can't install nothing in FSM (neither 9.99, nor 3.55 or anything i have tried so far).

If anyone can give any idea, help...if this because the hdd not being installed before the downgrading or cause another thing.
I think, that's cause of i didn't installed previous on the HDD (when at OFW) but...i don't know!!

Cheers!!
]]>
PS3 | Downgrading and Flashing ruroni http://www.ps3hax.net/showthread.php?t=78622
<![CDATA[What's the issue for this brick?]]> http://www.ps3hax.net/showthread.php?t=78621&goto=newpost Mon, 20 Oct 2014 22:44:39 GMT A friend of mine was downgrading his 2501 slim and he bricked it. He said he soldered a wire to the tristate but still same issue, the ps3 did not...
A friend of mine was downgrading his 2501 slim and he bricked it. He said he soldered a wire to the tristate but still same issue, the ps3 did not stay on. this below video isnt his but same exact issue. What could be the issue? not soldering the right way or just a total loss? He has 3 valid dumps.

http://youtu.be/dv5fPBZ1Lkk

thanks guys.
]]>
PS3 | Downgrading and Flashing ssjbrolly http://www.ps3hax.net/showthread.php?t=78621
CECH2xxx with strange Syscon Panic? http://www.ps3hax.net/showthread.php?t=78568&goto=newpost Sat, 18 Oct 2014 20:38:11 GMT So I received a CECH2000 series slim console a while back, and I managed to fix up some of the things it was missing from the case, and I got it all...
So I received a CECH2000 series slim console a while back, and I managed to fix up some of the things it was missing from the case, and I got it all up and running!

I noticed the previous owner had tried to downgrade it with a clip, but the chip did not seem to be damaged in any way. So I booted it up after replacing thermal paste, and it shows 9.99. So no need to flash it, woohoo! :)

So I decide to add a drive to it and get it remarried, but this is when the really odd situation begins to happen. Sometimes when I was in FSM, the console would not boot up, and sometimes it even after about 20-30 sec gave a RLOD and turned off. After a little while, I did manage to get it married to the drive, and then I got out of FSM.

Then I tested the drive, and it worked just fine with apps and all. I proceeded to toggleQA, and then update it to Rogero 3.7. Just as it was done and had booted up, it actually froze on the XMB! Then shortly after, it RLOD again and shut comepletely off. Greatly confused, I wondered what in the world was wrong... Then when I turned it off, it then preceded again to do the RLOD after 20-30sec trying to boot! Then I restarted again, and then it would boot, but again it just freezes randomly after boot, anything around 5sec to 3-4 minutes.

Soooo, apparently I have a console here which refuses to run no other firmwares than Rogero's 9.99 downgrader, and I honestly don't really know what to try. I managed after a lot of restarts and RLOD trouble and what not to install a 4.65 custom firmware, but the exact thing happened. Again with a lot of frustration to hopefully make it through a firmware installation (it just kept freezing or RLOD'ing) I got it back to Rogero's 9.99 firmware. And now it worked just fine, no freezing, no RLOD and just worked perfectly.

After this, I tried the following things:

1: I then tried to install a OFW 3.55, but this also resulted in the exact same issues above.

2: I hooked up my Teensy to check a dump from the console, and it was all just fine, both with manual and validation checks, and I triple checked all of the soldering. I even tried different patches to ROS and flash it back. The only thing the flashing did was to make it boot nicely once for some odd reason, but still with random freezing, even in safe mode / recovery mode.

So I really hope someone could shed some light on what is going on with this console. To me, it seems to be some kind of very odd syscon panic, but I am not sure at all. And no this is not an actual YLOD or temperature issues at all...

Cheers!
]]>
PS3 | Downgrading and Flashing lolerguy http://www.ps3hax.net/showthread.php?t=78568
self shutdown ps3 (tristte related) http://www.ps3hax.net/showthread.php?t=78536&goto=newpost Fri, 17 Oct 2014 17:25:51 GMT someone gave me a cfw ps3 thet turned off after5 sec w no blinking red light. swapped psu and srill the same prob. the ps3 was modded so i wired ...
someone gave me a cfw ps3 thet turned off after5 sec w no blinking red light. swapped psu and srill the same prob. the ps3 was modded so i wired tris-sbe and is stayed on. tooked 2 goof dumps and compared them. everything was fine. i patched them w habib465 and rogero old 355fsm and no result? any suggesetion, or what importance has tristate
]]>
PS3 | Downgrading and Flashing ortis123 http://www.ps3hax.net/showthread.php?t=78536
Damn E3 flasher Clip cable, someone please help!!!!!! http://www.ps3hax.net/showthread.php?t=78533&goto=newpost Fri, 17 Oct 2014 16:47:10 GMT Hello. I have received my E3 flasher bought brand new yesterday. I have a ps3 slim 2003b. I have connected the E3 cable clip but i keep getting error...
Hello. I have received my E3 flasher bought brand new yesterday. I have a ps3 slim 2003b. I have connected the E3 cable clip but i keep getting error 10001100. Iv'e tried putting tape, putting coins, and even soft foam rolled to make it very hard (I don't have hard foam). I also tried sanding the cable clip a bit to that the little transistors wont get in the way, and that worked out.

My problem is:

Anytime I try to clip the E3 cable to the NOR chip, one side will clip in, but the other side wont. And when I press on the other side, the opposite side goes up. It just won't clip BOTH sides fully. Please someone help me with is problem. I am completely stuck and it is my first time doing something like this.
]]>
PS3 | Downgrading and Flashing Motohama http://www.ps3hax.net/showthread.php?t=78533
beckup of nand ps3 corrupted http://www.ps3hax.net/showthread.php?t=78527&goto=newpost Fri, 17 Oct 2014 14:12:30 GMT good afternoon ! I have a fat ps3 and did beckup your nand and came just corrupted . Menha Ducia is . as I have caught outtra board of the same...
good afternoon ! I have a fat ps3 and did beckup your nand and came just corrupted . Menha Ducia is .
as I have caught outtra board of the same model and ussar your nand neete device. Example . my corrompito this is a fat ps3 plava vee 001
and a good
ps3 fat plava vee 001
I subistituir the nand ?
or she has as recustruir , corrupted my nand ? my ps3 gave Standings bkink
if you send me the link .
This has forced my
]]>
PS3 | Downgrading and Flashing galeguim http://www.ps3hax.net/showthread.php?t=78527
Problems after removing E3 Linker http://www.ps3hax.net/showthread.php?t=78495&goto=newpost Thu, 16 Oct 2014 09:00:13 GMT Hi, Removed my E3 linker yesterday and now my PS3 powers with no video or hdd activity. I have read about bricks after flashing but I never flashed...
Hi,
Removed my E3 linker yesterday and now my PS3 powers with no video or hdd activity. I have read about bricks after flashing but I never flashed my PS3 and I do not have any original dumps. Do I need to reconnect the point either side of the cut trace and if so will this fix the problem.

Thanks
Finchy.
]]>
PS3 | Downgrading and Flashing finchy70 http://www.ps3hax.net/showthread.php?t=78495
GLOD Turning Off after 30 Seconds http://www.ps3hax.net/showthread.php?t=78478&goto=newpost Wed, 15 Oct 2014 17:20:31 GMT I have another weird case, this one turn on (No HDD or USB activity, not a single time the hdd led lights up) and after 30 seconds it goes off. Gpu...
I have another weird case, this one turn on (No HDD or USB activity, not a single time the hdd led lights up) and after 30 seconds it goes off.
Gpu and CPU gets Hot.
Soldered tristate and the box stays ON, dumped, Dump is 100% OK with different patchers.
Ros0 3.66 Ros1 3.70, patched for 3.55, flashed, removed tristate, turned ON same result :banghead:.
WTH ? Of course it's another CECHL :shot:

Any tips ?
]]>
PS3 | Downgrading and Flashing passete http://www.ps3hax.net/showthread.php?t=78478
Downgrade CECH-G04 SEM-001 problem http://www.ps3hax.net/showthread.php?t=78467&goto=newpost Wed, 15 Oct 2014 10:57:44 GMT
Hello to everyone! I have a CECH-G04 SEM-001 ps3 console with OFW 4.46. I ' ve tried to downgraded it but when I merged the dump files with the flowrebuilder* I saw the popup: OPERATION COMPLETED WITH ERRORS!
0 bad block(s) has been found on NAND 0
2 bad block(s) has been found on NAND 1
After that I ignore that error because in another console with the same error I complete the progress with succes. However i patched the dump file i splited it. When i put the patched dump files back to ps3 i saw YLOD.
Could anyone help with this problem???
]]>
PS3 | Downgrading and Flashing polog40 http://www.ps3hax.net/showthread.php?t=78467
HELP!!!!!! I THINK I BRICKED http://www.ps3hax.net/showthread.php?t=78436&goto=newpost Tue, 14 Oct 2014 04:40:12 GMT :banghead: I 3 valid dumps at least i think their valid. Well come up the black to what ever i flash to it. I have tried bwe nor,ps3 dump checker,nor...
:banghead: I 3 valid dumps at least i think their valid. Well come up the black to what ever i flash to it. I have tried bwe nor,ps3 dump checker,nor patch,ps3 flash tool. All 3 dumps dump come back ok. I have tried patching 3.55,4.50,auto patcher still black screen tri-state is hooked up to the sbe on the e3 linker i am solder in.

Still black screen please help being on this for a week:banghead::hmmmm2:

CECHK-01
DIA-002
E3FLASHER WITH ELINKER
ON 4.60 OFW
]]>
PS3 | Downgrading and Flashing scorchedwynd http://www.ps3hax.net/showthread.php?t=78436