[baileyscream]

***ADDED LIST OF ITEMS I BOUGHT AND WHERE I BOUGHT THEM FROM AT BOTTOM OFF POST FOR ANYONE WANTING THE SAME***

ok i have been wanting rear usb ports on my ps3 slim since i bought it (3 months ago)
the only guide i found was this:-
http://www.ps3hax.net/showthread.php?t=21940
by j0nnymofo

*****edit if you have a phat ps3 also have a look at this buy GregoryRasputin :-
http://www.ps3hax.net/showthread.php?t=11269 end*****

but you can only use the front or rear one at a time not together
also i have my tv wall mounted and a usb cable extention running in the wall so i can attach a pseye without the wires showing
j0nnymofo's mod would also need a booster putting in for the extra usb cable lenth.
so after alot of searching i found that all the usb hubs you can buy from pound shops are usless even for normal use on any ps3.



but then i found this in my spare pc parts box

i plugged it into my ps3 as normal then plugged the hidden usbextention going up to my tv and pluged my pseye into that and it worked (if i plugged the usbextention directly into the ps3 without this hub then i get "no pseye detected" on screen)

so on with the hard mod



the tools i used



the ps3



open it up (there are enough guides out there if you have never done this)

carry on and strip the ps3 slim right down to the main board



desolder and remove the usb pins from the main board
this is done by inserting a thin flat screwdriver or as i did it a stanley blade between the usb housing and mainboard (where the red line is in the pic) and desolder the 3 shilding legs highlited in the blue circle's while using the blade to help seperate the usb from mainboard.
then desoler the 8 usb legs highlited in the orange circle's then carefully tilt the usb's forward back towards the board untill you can pop port 2's legs out of the board (the help of a small screwdriver will prob help here also make sure all the legs are compleatlydesoldered or they wont move)



cut a controller usb charging cable in half and the half with the small usb connector needs soldering to the main board where the usb pins have just been delodered from in this order:-
with usb on main board facing you solder wires from left to right red white green black



then solder the other half of the usb cable to the usb pins in the exact same order.
re-seat the usb back in place and re-solder the port 1's pins &shild legs back to the mainboard



remove the rubber from the small usb (this helps it to fit in place better when the ps3 is finnished)



drill a hole in the top half of the heatshild for the wires you have just attached to pass through (the blue highlight is where the front usb's are located when this heatshild is attached to the mainboard)



heat glue the wires into this position



pass the wires through the hole you just drilled




cut the heatshild to fit the twin usb connector where the optical out is situated and check it fits




remove / desolder the optical out from the main board. very simple only 3 solder points to desolder and it will pop off. there are 2 small resistors under the optical out that don’t get in the way so can be left where they are.



solder another cut in half charger cable to the double usbconector in the same order as the front



put the usbconector in place and run the cable inside the heatshild in the same direction as shown in pic also notice some of the black plastic on the rear usb has been cut away to make room for the resistors on the board.



place the top heatshild onto the mainboard and holding the usb in place apply a small amount of heat glue to hold in place.



then heat glue the usb and wires in place on the inside.



re-build the mainboard and heatshelds back together and cut the optical out hole on the plastic lower half of the ps3 shell large enough to alow for access to the new usb ports



sit the mainboard/heatshilds back into the lower half of the ps3 housing and heat glue the rear wires in place as shown here then attach the bdvd back in place



DO NOT REMOVE THE CARD READERS AS I DID HERE AS THE USB HUB WILL STOP WORKING CORRECTLY AS I DESCOVERED AFTER I HAD RE-BUILT THE PS3



the replacement usb hub!!!!! i cannot find a black box brand one anywhere so bought this one from e-bay




remove the usb's from the usb hub (NOT THE CARD READERS AS SHOWN HERE) and solder the 2 rear and 1 front usb wires as shown here (remember the usb wire from the mainboard has the small usb connector and that can now be plugged into the hub



place the wires and usb hub as shown



heat glue the wires and usb hub to the top of the bdvd as shown



close ps3 back up and test


please feel free to ask questions and no this has NOTHING to do with 3.56 / 3.60 / 3.61 custom firmware so DO NOT ASK

ok for those of you wondering why i wanted internal rear usb's and not just attach a usb hub to the front this is why:-




as you can see there are NO wires on show (highlited in the black box) also note the pseye has its base removed and is mounted below the tv (if you remove a small round "pad" from under its base it will fit over the pseye power light. a quick tip for them that are irratated by the bright led light)

i have it all neat and having wires allover would look cluttered

***LIST OF PARTS*

2x Female USB Dual A Type Connector PCB Mount Socket
http://cgi.ebay.co.uk/ws/eBayISAPI.d...STRK:MEBDIX:IT

PS3 SLIM CONSOLE OPENING TOOL TORX T8 - PROFESSIONAL
http://cgi.ebay.co.uk/ws/eBayISAPI.d...STRK:MEBDIX:IT

65 IN 1 COMBO MEMORY CARD READER SD CF + 3 PORT USB HUB
http://cgi.ebay.co.uk/ws/eBayISAPI.d...=STRK:MEWNX:IT

AND FOR THEM ASKING ABOUT THE ITEMS IN THE LAST 3 PIC'S:-

Cool Decal Sticker Skin For Sony PS3 Slim&2 Controllers
http://cgi.ebay.co.uk/ws/eBayISAPI.d...=STRK:MEWNX:IT

MOVE Controller Console Stand Charge Dock For PS3 Slim
http://cgi.ebay.co.uk/ws/eBayISAPI.d...STRK:MEBDIX:IT

Brand Postposition cooling Fans for ps3 slim console
http://cgi.ebay.co.uk/ws/eBayISAPI.d...STRK:MEBDIX:IT

[Pirate]

We at PS3Hax like to highlight our members work towards the PS3 scene. PS3Hax user, baileyscream has written a tutorial on how to install a dual-USB modification on your slim PS3 via USB Hub.

[Pirate]

Moved to front page!

[Brenza]

Not very useful..

And you don't show how to link che hub to the ps3.
Anyway you could just use the hub as external device, i don't like cut the ps3's skin

[Wolfie708]

Originally Posted by Brenza Not very useful.. And you don't show how to link che hub to the ps3. Anyway you could just use the hub as external device, i don't like cut the ps3's skin

Just plugging in the hub defeats the object though. This is about getting USB sockets on rear of PS3.

I also hate cables coming from front, and have no problem cutting things up lol

[OoZic]

Nice DIY project with good pictures

Though I do think an usb expander, like the logic3 nicely fitting on the front with 5 usb ports, is an easier way

[baileyscream]

i will be posting more pics and editing the post later
i didnt want anything plugged into the front usb's making it look cluttered and as i use a pseye that is plugged into the ps3 all the time then i wanted the wire out of site
if you would like to tell me you would like to see in the pics then just ask and i will get them taken
************* [ - Post Merged - ] *************

Originally Posted by OoZic Nice DIY project with good pictures Though I do think an usb expander, like the logic3 nicely fitting on the front with 5 usb ports, is an easier way

the problem with this is i have a hidden usb extention in the wall and this 5 port and also a 4 port that "clips on" i found on e-bay do not boost the signal so the pseye will work

[BobbyBlunt]

Originally Posted by Brenza Not very useful.. And you don't show how to link che hub to the ps3. Anyway you could just use the hub as external device, i don't like cut the ps3's skin

This is useful. The PS3 should've had rear USB ports to start anyway. Also do not put down someone else's work. We frown upon that here.

[mikhael]

Sharing knowledge... always a A+ to me

[aaron101]

looks awesome so ignore the haters more pis and more detail would be great cheers.