[kada]

FW was 3.55 kmeaw then I soldered teensy ++ so I think at least i have 3.55 kmeaw dump.Then I installed ofw 3.55 when teensy still soldered(not connected to pc) then updated 3.61 but my dumps are unknown.maybe problem i update teensy soldered?

[judges]

Originally Posted by kada FW was 3.55 kmeaw then I soldered teensy ++ so I think at least i have 3.55 kmeaw dump.Then I installed ofw 3.55 when teensy still soldered(not connected to pc) then updated 3.61 but my dumps are unknown.maybe problem i update teensy soldered?

norpatch.exe does only recognize OFWs, so it would report a 3.55 kmeaw (and any other CFW) as unknown. But if you updated to 3.61 (doesn't matter whether teensy is soldered) and dumped your flash again, norpatch should recognize it. If it doesn't it's most likely that your dump is corrupt (-> check wiring).

[kada]

I desoldered and reflash 3.61 and resoldered teensy but still same.MB rev DYN-001 is there any additional wires?

Edit:

I checked wires and solder pads, changed USB cable reflash teensy.Still unknown version by norpatcher.
I'm using win7 x64.I cant get what im doing wrong...

I think its wiring problem but im using 80pin IDE HDD cable wires.these are used for data carrying

[judges]

Originally Posted by kada I desoldered and reflash 3.61 and resoldered teensy but still same.MB rev DYN-001 is there any additional wires? Edit: I checked wires and solder pads, changed USB cable reflash teensy.Still unknown version by norpatcher. I'm using win7 x64.I cant get what im doing wrong... I think its wiring problem but im using 80pin IDE HDD cable wires.these are used for data carrying

After inspecting the dumps you've send me, it seems like your wiring might actually be okay. Still both of your dumps are corrupted.

What NORway version are you using?
Have you recompiled the source?
Are you using a voltage regulator?
Were both dumps made with the same wiring?

[kada]

Norway 0.3,
I'm using voltage regulator dumps are from same wiring.
i didnt compile source just use hex provided.

[toxie]

Originally Posted by kada Norway 0.3, I'm using voltage regulator dumps are from same wiring. i didnt compile source just use hex provided.

After every dump, you`re getting different dumps ?

[bpear96]

Hey, looks like this is making some great progress. i really want one for my ps3 but 1. dont have a soldering iron 2. never soldered before 3. dont want to screw things up so.. i was wondering if there is anyone out there who would be willing to solder it for me. Like maybe i could ship it to you can you solder it for me then send it back. Right now im just looking to see how much someone would charge to do this. Prefer someone in the USA. Also you need to somehow prove you are a trustworthy person

[jarmster]

I use to use wire wrap wire for all my mods, i never really liked it. Brittle
Then i seen someones post about the kynar wire. Its very similar to the wire wrap wire but i thought the quality was 10 fold better. I had no problems with wires breaking while taking insulation of the ends. If your going to do the mod, do it right. Keep the wires short (under a foot) and use the right wire. I picked up a 50' roll of the kynar for 6 bucks.
You may have your wiring all right but too much copper between test point and teensy can cause issues. Less is always better. Good luck

[kada]

Originally Posted by toxie After every dump, you`re getting different dumps ?

They are similar.I dont check all but first codes all same.Is there any COM settings do i need to change.

And my nor is Samsung brand.judges said maybe this effect.Is here anyone succeed with Samsung nor.

[calimba]

Originally Posted by kada They are similar.I dont check all but first codes all same.Is there any COM settings do i need to change. And my nor is Samsung brand.judges said maybe this effect.Is here anyone succeed with Samsung nor.

if you have this error with samsung nor:

C:\....\teensy>NORway.py COM3 write flash.bin Pinging... Set SB to tristate STATUS_DRIVE: False STATUS_TRIST_N: True STATUS_RESET_N: True STATUS_READY: True STATUS_CE_N: False STATUS_WE_N: True STATUS_OE_N: True Resetting NOR... Ready. Sector 000000 (1/128) [M]... Traceback (most recent call last): File "C:\....\teensy\NORway.py", line 320, in <module> n.writerange(addr, data) File "C:\....\teensy\NORway.py", line 210, in writerange self.writesector(addr/2, data[:0x20000]) File "C:\....\teensy\NORway.py", line 177, in writesector raise NORError("Verification failed") __main__.NORError: Verification failed

unfortunately your NOR device have bad sectors and need change