[judges]

Originally Posted by zaf This is just impossible. erasechip finishes in 2 minutes but nothing is erased!!! I get the same exact dump just like before with same MD5!!!

Well, then there's not much I can do here.

Again, check your signal lines (OE, WE, CE, RY/BY). Not just for resistance, but maybe you've swapped two of them or something like that. And also, again, try CrackMyDay's method. Not just sort of, but to the letter.

[judges]

I've updated norpatch.exe to recognize the new OFW 4.10 in your dumps. You'll find the download link in the 1st post of this thread (github)...

-- judges

[Bohemio]

(First Sorry 4 my english, i do my best) .... i have a problem with a PS3 160gb CECH2511a, with Spansion S29GL128N ... i solder my Teensy++ , i extract 3 or 4 dumps , and i verify they correct.... i extracted, i apply the 6 patchs , when i re write the nor, the process finish, i power on the ps3 , and shut down in 1 or 2 seconds.... if i Write the original dump , work again..... the dump is OK , but dont work when i apply the patch.


I add you the original dump[QUOTE]
http://www.mediafire.com/file/yc57m1...f6c/alfin2.bin

[sguerrini97]

Hi, I'm preparing to solder my Teensy++ to my PS3.
What kind of cable it's better?
THIS (the red one, wire-up 0,2mm)

or this



?

Or can someone suggest me a right cable? Thanks.

The CrackMyDay's method can be use on different nor memory? Because i haven't the 3.3v regulator.. If yes, I need to solder the 3.3 input in all NOR Vcc or only in one of them?

And please can someone upload the NORWay v0.4 beta12? Multiupload seems to be offline now.. Thanks.
Sorry for my english.

[judges]

Originally Posted by sguerrini97 Hi, I'm preparing to solder my Teensy++ to my PS3. What kind of cable it's better? THIS (the red one, wire-up 0,2mm) or this

The first one seems to be okay (0.2mm). The one on the picture looks kind of thick.. Of course it will work as well, but you might get problems routing the wires if you target a permanent install of your teensy. For the 0.2mm wire you might wanna consider soldering 2 or 3 wires for the ground connection.

Originally Posted by sguerrini97 The CrackMyDay's method can be use on different nor memory? Because i haven't the 3.3v regulator.. If yes, I need to solder the 3.3 input in all NOR Vcc or only in one of them?

Yes, you can use it for all kinds of NORs, although I've never tested it myself. Don't really understand your second question. You pick up the 3.3V supply (ONE) from the console and solder it to your teensy according to the instructions.

Originally Posted by sguerrini97 And please can someone upload the NORWay v0.4 beta12? Multiupload seems to be offline now.. Thanks. Sorry for my english.

Here you go:
https://rapidshare.com/files/3990712...y_04beta12.zip

[sguerrini97]

Originally Posted by judges The first one seems to be okay (0.2mm). The one on the picture looks kind of thick.. Of course it will work as well, but you might get problems routing the wires if you target a permanent install of your teensy. For the 0.2mm wire you might wanna consider soldering 2 or 3 wires for the ground connection. Yes, you can use it for all kinds of NORs, although I've never tested it myself. Don't really understand your second question. You pick up the 3.3V supply (ONE) from the console and solder it to your teensy according to the instructions. Here you go: https://rapidshare.com/files/3990712...y_04beta12.zip

Thank you very much for your help
But what's the 3.3V supply of the console? I was thinking that on the diagram was "NOR_Vcc", but in the diagram of my motherboard (JSD-001) there are 2 "NOR_Vcc"..

And i'ts possible to run NORWay under linux? Thanks.

[judges]

Originally Posted by sguerrini97 Thank you very much for your help But what's the 3.3V supply of the console? I was thinking that on the diagram was "NOR_Vcc", but in the diagram of my motherboard (JSD-001) there are 2 "NOR_Vcc".. And i'ts possible to run NORWay under linux? Thanks.

Either one of the NOR Vcc pads will do. And yes, you can run NORway on linux, it's just a python script. But don't ask me how, I'm not a linux guy...

[TizzyT]

Originally Posted by sguerrini97 Hi, I'm preparing to solder my Teensy++ to my PS3. What kind of cable it's better? THIS (the red one, wire-up 0,2mm) or this ? Or can someone suggest me a right cable? Thanks. The CrackMyDay's method can be use on different nor memory? Because i haven't the 3.3v regulator.. If yes, I need to solder the 3.3 input in all NOR Vcc or only in one of them? And please can someone upload the NORWay v0.4 beta12? Multiupload seems to be offline now.. Thanks. Sorry for my english.

If you have any IDE cables laying around for those old IDE harddrives and disc drives I find those to be very good to solder with .

[sguerrini97]

Thank you again judges.

====

Originally Posted by TizzyT If you have any IDE cables laying around for those old IDE harddrives and disc drives I find those to be very good to solder with .

Are you talking about this?

[TizzyT]

Originally Posted by sguerrini97 Thank you again judges. ==== Are you talking about this?

Yes that it, I just peel each wire off and use them to solder, it works very well for me at least. Ask around if you would like and get opinion on it. If you need a larger size use a floppy cable they work as well. I don't solder a lot but when I do I use those as its easy to work with.