[Cypherous]

Originally Posted by thepitt Um .... Have you not been around long enough to experience "solderless" solutions. These clips are totally worthless and are plagued with bending pin problems, not fitting correctly; basically they have a very high failure rate. You don't hear much about that due to the small amount of these products in circulation and some sites that like to censor negative comments about their advertisers products. Soldering, if done correctly, is the way to go. With that said I am glad to see a dual boot solution and if I weren't in the USA and could afford such a product I would buy one right away (and rip the clips off and solder it on). I'm anticipating FFXIII-2, already pre-ordered it, but will be left with a dream of actually being able to play it. Props to dual boot & down with the clips!

I too have it preordered.

The issue i have is i don't want to risk anything at all with soldering, i have no skill at it myself and i don't know anyone with the skills i trust enough, so sadly a NAND clip is about my only choice

There will always be issues with products in their early stages and thats acceptable, it might take a bit of time but i have faith they can make a decent one, and even if i end up replacing it once or twice its still cheaper than a PS3 replacement should something go wrong

[Dusky]

So they finally did it huh? :P.

Now if only I had the money to actually BUY one

[Eugeneishere]

I have a question!What is the main process of downgrade?Because i want only to play backups on my PS3.I Buy e3 Flasher,put it on,do the downgrade(do i need to connect HDD for this process via that HDD station??),if downgrade succeed i can remove it?put my hdd,and forget about e3 flasher?

[playerkp420]

Originally Posted by Eugeneishere I have a question!What is the main process of downgrade?Because i want only to play backups on my PS3.I Buy e3 Flasher,put it on,do the downgrade(do i need to connect HDD for this process via that HDD station??),if downgrade succeed i can remove it?put my hdd,and forget about e3 flasher?

Yes, after downgrading with e3 flasher, you can remove the flasher from the system and plug your hard drive in.

But if you want to dual boot, you would need the flasher still hooked up.

[Eugeneishere]

So,if i remove it,i can forget about it?You cant use it on another console?

[playerkp420]

Originally Posted by Eugeneishere So,if i remove it,i can forget about it?You cant use it on another console?

Yep. I have done about 4 consoles.

[wander]

Hi guys.
There is a PS3 Slim 320gb, Data Code 1C, CECH-3008B.
How do I downgrade?

[stussy1]

alright dudes here is my problem i have a friend who has accedently updated his ps3 to
4.10 now my question is does this e3 flasher downgrade from 4.10 and also i heard there are problems with the nor clip not goin on properly sometimes do they sell the clip seperetly if i end up stuffing it
i am always reading forums and keeping up to date and looks pretty straight forward
the ps3 was on kmeaw before it is a slim cech-2502a model and also can i go back on to kmeaw if it requires qa flaging back to 3.41 no prob is there anything else i need to no
at the moment i am telling the person if she ends up taking it to the shop and finds out
if it will cost $60 or more she is better off getting the e3 flasher at least if anyone has problems in the future we have the flasher and also can i take out flasher after its done
and also is there any soldering involved or is that just for the dual boot
************* [ - Post Merged - ] *************

Originally Posted by wander Hi guys. There is a PS3 Slim 320gb, Data Code 1C, CECH-3008B. How do I downgrade?

dont think you can downgrade with that one base should be 3.66 firmware on that ps3 you cant downgrade past your lowest firmware or else you will brick

[arcadekidflo]

Is there any ESATA Dock with 2 bays connectors for easy swapping with a touch of o button ?