[oceansoul]

I buy PS3 Fat 60GB with motherboard cok-002

Bricked Firmware on this ps3 station was downgrade Rogero CFW 3.55 and bricked with overwrite with kmeaw 3.55 !
Ps3 cant turn off i need help if is posibel to fix ps3

COK-002
Serials 1-873-513-31
Backwards Compatability PS1 + PS2, Software Compatibility
Flash Storage 2x128MB NAND (Samsung K9F1G08U0A-PIB0)
Cell/RSX 90nm/90nm
Watts/Max 200/380

Topside motherboard:


Bottomside motherboard:


I need help with this board i have e3 flasher is it posible to fix with e3 this board with samsung 2 nand chips and how ?
Also need help with tristate is this board have it tristate becouse its nand ?
please provide me some guide also i dont have working backup of bios ! IS posible to fix this board ?


Thanks

[carldenning]

u cant do anythink with the e3 flasher becuse its only for a nor ps3 and yours is a nand , maybe a proskeet will as that is for a nand

[oceansoul]

Thanks for answer but on e3 website stay that is support for nand few weeks long go i think that is maybe new one suppport but seems it didnt that must wait for special nand with 2 clips !

Thanks friend !

[OGzxFTW]

You bought a downgraded console so im guessing you dont have the original backup dump
Your console is bricked and without that dump you can not reflash
A hardware flasher wont work for you either, its permabrick

[oceansoul]

I dont have backup dump ! Is it posible that I use backup from same cok-002 with samsung nand of someone else ?
To ask someone to attach or send me when e3 flasher come out for few weeks ?

[jhax78]

Originally Posted by oceansoul I dont have backup dump ! Is it posible that I use backup from same cok-002 with samsung nand of someone else ? To ask someone to attach or send me when e3 flasher come out for few weeks ?

1st why did you even switch to kmeaw?
rogero is based on that and it worked
i see no point even to go from cfw 3.55 to cfw 3.55

2nd you can't use a backup from another console ever

E3 is full of **** get progskeet and hope the dumps are intact

the per console data would be intact i think as you only used a pup
and not some patched dumps

[oceansoul]

jhax78 thanks for replay but if you read my post you will see that i buy console bricked i dont update anything and doesnt no why he owerwrite console rogeros with kmeaw and i dont have bios backup also as i post already.
Only what i wont if is posible to run console and make tham work i dont brick this console when i buy guy what sold me told that he brick tham that way and that is posible to fix ... and i goolge it and see witout original backup that is not posible but i use this console to play and try to make tham work .

[jhax78]

Originally Posted by oceansoul jhax78 thanks for replay but if you read my post you will see that i buy console bricked i dont update anything and doesnt no why he owerwrite console rogeros with kmeaw and i dont have bios backup also as i post already. Only what i wont if is posible to run console and make tham work i dont brick this console when i buy guy what sold me told that he brick tham that way and that is posible to fix ... and i goolge it and see witout original backup that is not posible but i use this console to play and try to make tham work .

ok i apologize if it looked like flaming it was not trust me

steps to try

1 use a dongle to enter service mode and install a pup that way
with the right lv2diagfile (there will be a log on the usb if this fails)

2 use progskeet flasher to make backups of the nands and look if your per console data is intact <-- should be because like you say theres only a pup
installed and maybe patch it so it will atleast work again

E3 won't come with a nand flasher soon im pretty sure

[oceansoul]

nope its not flame for sure I just say that i wont to buy 1 ps3 cheeper and try to fix tham but its not easy way maybe that is nor and spansion chip everything will be much easy

Also i cant go to factory mode i have usb tongle p3go and ylod doesnt give me chance to go anywhere just yellow than red light blinking ! Refalow doesnt help becouse its some firmware brick and console cant boot ! I would love that is posible to factory / service mode but cant !

For progskeet i cant play with lot wires im not expert just need to wait also nand clips for dual nand flash clip !