[infinity_kol]

http://www.mediafire.com/?ucc7w1517m3kdwb
please check my ofw file dump with progskeet

[renanbianchi]

Originally Posted by infinity_kol http://www.mediafire.com/?ucc7w1517m3kdwb please check my ofw file dump with progskeet

Great work. Dumped perfectly. Now use autopatch files on progskeet to autopatch the dump as said here:

http://ps3devwiki.com/wiki/Downgradi...re_flasher#NOR

[infinity_kol]

Thank U! But what exact process of checking dump taken by progskeet. can u explain me?

Following file and folder created by Flowrebuilder from my dump...

01. asecure_loader (file folder) size 58.2 kb
02. ros0 (file folder) size 5.68 mb
03. ros1 (file folder) size 5.69 mb
04. boatloader_0 (file) size 90 kb
05. cCSD (file) size 2 kb
06. cISD (file) size 2 kb
07. cvtrm (file) size 256 kb
08. eEID (file) size 64 kb
09. trvk_pkg0 (file) size 128 kb
10. trvk_pkg1 (file) size 128 kb
11. trvk_prg0 (file) size 128 kb
12. trvk_prg1 (file) size 128 kb

Read more: http://www.ps3hax.net/showthread.php...#ixzz1nnuMhr49


thanks in advance.

[renanbianchi]

Originally Posted by infinity_kol Thank U! But what exact process of checking dump taken by progskeet. can u explain me? Following file and folder created by Flowrebuilder from my dump... 01. asecure_loader (file folder) size 58.2 kb 02. ros0 (file folder) size 5.68 mb 03. ros1 (file folder) size 5.69 mb 04. boatloader_0 (file) size 90 kb 05. cCSD (file) size 2 kb 06. cISD (file) size 2 kb 07. cvtrm (file) size 256 kb 08. eEID (file) size 64 kb 09. trvk_pkg0 (file) size 128 kb 10. trvk_pkg1 (file) size 128 kb 11. trvk_prg0 (file) size 128 kb 12. trvk_prg1 (file) size 128 kb thanks in advance.

download and extract this file:

http://www.mirrorcreator.com/files/1...ches.rar_links

open winskeet, click on patch tab, Input file: your nor dump.

Patch file: progskeet_patch.txt

Winskeet will apply the patches from the patch1 and rvk-040000 patches.

after that, just flash it back. Read: http://ps3devwiki.com/wiki/Downgradi...y_Service_Mode

[infinity_kol]

I applied all patches manually and see size is ok,
then flashed to ps3 with result of verification address failed.
Dumed again and checked with hex editor it is not matching with flashed one.
reflashed again same verification failed error. reflash ofw and dumped. matched with ofw dumped earlier but not matching. i think progskeet not writing well.
is it the problem of progskeet not writing but reading fine.

Now i think i m on semi brick position.

please give me any suggestion .

thank you.

[renanbianchi]

Originally Posted by infinity_kol I applied all patches manually and see size is ok, then flashed to ps3 with result of verificatio address failed. Dumed again and checked with hex editor it is matching with flashed one. reflashed againd same verification failed error. is it the problem of progskeet not writing but reading fine. Now i think i m on semi brick position. please give me any suggestion . thank you.

Upload the bad flashed dump so that i can verify it. Check your usb port/Cable and yout GND wires. Also try not to turn the PS3 off.

[domelec]

recheck all wires cos verification errors is most likely bad wiring
also how thick are the wires u are using ?
what nor is it?
which winskeet version u using?
just to name a few questions that need answering

[infinity_kol]

I used "Winskeet111205", Nor name is "Spansion s29gl128p90tfir2", i dumped bad flashed file and open in hex editor it shows maximum "00 FF". i have also uploaded OFW file. when i am using another flasher like progskeetxxxxx_a, it gives me error "device not found" mean not detecting ps3 nor, but with "Winskeet111205" it detects well. where is the problem not detected by "progskeetxxxxx" flasher etc.

[domelec]

older winskeet and progskeet flasher software uses older driver libusb0

run zadig and change driver from winusb to libusb0

then try WinSkeet40000_111004

[ariepoenya]

now to uses JB2 in system rogero proskeet,please help?