[blaxoul]

Hi when i am soldering a cable to a point, A point with its copper has been romeved from main board with accidentanly. I think soldering iron was too hot.

So any ideas about to fix that. Where does a point goes? So i can solder the cable the other side of a point?

[blaxoul]

As i explained my previous message, my a and b point is scracthed now. And i can not solder anything on A point because of my previous topic. After this mistake i installed e3 flasher. When i turn on ps3, all green leds ok, power led ok but the blue leds changes always like that 10101010 and then 01010101. and this is a loop. On tv there is no signal always. and my esata station's data led is always off. I tested my sata station with my computer there is no problem with it.

But when i un-install (except nor-clip) e3 flasher and then plug ps3 harddisk to e3 flasher's slot, my ps3 opens perfectly and there is no problem.

My ps3 is slim and factory firmware is 3.40.

So, what is the problem? Because of scrached way between a and b, or anything else? whats your opinions and suggestions?

[blaxoul]

No one to answer about this problem? I need some support. Thank you.

[hellsing9]

Something wrong with the flex maybe, or the flasher.
Try to post in this thread the image, because is broken.

[blaxoul]

Originally Posted by hellsing9 Something wrong with the flex maybe, or the flasher. Try to post in this thread the image, because is broken.

forum admins has merged my two topics. SO my first topic is now first message of this topic. I will try to add an image this night. I wonder that, now there is no electrical way between A and B point. My ps3 works great with its OFW and without e3 flasher. But when i connect e3 flasher to ps3, i get that problem which i mentioned previous messages of this topic. When i power on ps3, the blue leds are always 10101010 and 01010101 and this is a loop.

[hellsing9]

Was me who merged threads, it's the same issue and you will get a quicker response.
Please upload the pic to = imageshack.us or photobucket to get a better view of that board.

If you don't have connection way from A to B, how do you expect to work?.
It's confusing, when you upload the image post it here and let me know.

Check this : E3 Flasher tutorial

[blaxoul]

I am not at home now, so i will upload photo this night. Let me clear that,

First i opened my ps3 and scratched the way between A and B point. Then when i was trying the solder a cable for fast dual boot to A point, because of hot soldering iron, whole A point with its copper has been removed from mainboard (i think that section will be more clear when i upload pics.)

Anyway, now i am sure that there is no electrical way between A and B point and my ps3 works without e3 flasher. When i install e3 flasher all blue leds 10101010 and then 2 seconds later they are 01010101 and 2 secs later 10101010 and 2 secs later 01010101... This is a loop. In e3 flasher there is no explain about this led situations. ALso, there is signal on tv and sata station data led is off. I want to ask that, what is the duty of A and B point. Where does A point go to electrically and also B point? (for example, a point goes to nor flash or cpu vs.) Why my ps3 works if there is now way between A and B and without e3flasher?

Its a little strange, i accept that. I will be happy, if someone can explained that because i am confused too

[lrtopshot]

???????????????????????????????

??????????

[blaxoul]

Originally Posted by lrtopshot ??????????????????????????????? ??????????

When we want to use fast dual boot, we have to scratch it. But now, my problem is not that. If you read my previous message, you can see what my problem is.

[hellsing9]

What you mean..by *scracth it*?.