|
|
03-31-2012
|
#1 |
|
Member
 Join Date: Feb 2012
Posts: 33
Likes: 0
Liked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
E3 Nor Cable Clip - best long term reinforcement solution?
How do I keep this ****in thing down on the chip for longer than 1 day?
-Used sticky tape (down HARD, DONT question me about this) -Hard foam (yes it was hard foam NOT soft) on tape layer (foam height is very high - 2.5" that I need to press MBoard down HAARD! while I screw back first few MBoard screws for re-assembly) My reinforcement lasted long enough to reflash my bios immediately after I re-assembled the PS3. Couple days later, attempt another backup and the clips ****in loose. Whos got the best E3 clip long term reinforcement solution? |
|
|
|
03-31-2012
|
#2 |
|
Member
 
Join Date: Feb 2012
Posts: 357
Likes: 163
Liked 90 Times in 66 Posts
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
|
The only answer is...soldering
__________________
PS3 Slim 250GB - CECH-2004B 3.55 Rogero v3.1 (E3 Flasher)
 |
|
|
|
|
03-31-2012
|
#3 |
|
Apprentice
Join Date: Nov 2011
Posts: 7
Likes: 0
Liked 1 Time in 1 Post
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Either that or epoxy but makes sure everything is aligned before doing that or you will be screwed lol.
|
|
|
|
|
03-31-2012
|
#4 |
|
Member
Join Date: Feb 2012
Posts: 357
Likes: 163
Liked 90 Times in 66 Posts
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
|
Epoxy is more permanent than soldering - you can desolder
__________________
PS3 Slim 250GB - CECH-2004B 3.55 Rogero v3.1 (E3 Flasher)
|
|
|
|
|
03-31-2012
|
#5 | |
|
Senior Member
 Join Date: Dec 2011
Posts: 4,685
Likes: 1,039
Liked 1,642 Times in 1,180 Posts
Mentioned: 850 Post(s)
Tagged: 0 Thread(s)
|
If you have a model that has those little transistors in the way, you can shave a little plastic off the clip. But soldering would be the best solution. You can use the e3 linker to solder the points to. Then it plugs in onto the flasher.
__________________
HOW TO DOWNGRADE W/E3 FLASHER TO ANY OFW/CFW
Nor model PS3 downgrade service in U.S.A. if you don't want to do it yourself For downgrade help join irc at effnet-Just enter name and channel is #ps3downgrade |
|
|
|
|
03-31-2012
|
#6 |
|
Member
Join Date: Mar 2012
Posts: 35
Likes: 0
Liked 7 Times in 6 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Can you Desolder after solder e3 linker? Im having hard time for the clip suit too. Always failed to read nor. I tried over 50+ times.
E3 linker work on 4.11 ps3 slim? It's there any tutorial teach how to solder e3 linker? Also e3 linker can downgrade multiple device right? Thank you so much |
|
|
|
|
03-31-2012
|
#7 |
|
Member
Join Date: Feb 2012
Posts: 357
Likes: 163
Liked 90 Times in 66 Posts
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
|
Yes you can desolder E3 Linker you just have to be very carefull when doing so, you better get help if you want to do it. Also it gives a fail to read nor when ps3 starts up because PS3 is busy using it, wait 40 sec before you attempt to make a back-up, if it gives you the fail to initialise back-up - you have to open your PS3 again and allign your clip precisely and stick it hard
__________________
PS3 Slim 250GB - CECH-2004B 3.55 Rogero v3.1 (E3 Flasher)
|
|
|
|
|
03-31-2012
|
#8 |
|
Member
Join Date: Mar 2012
Posts: 35
Likes: 0
Liked 7 Times in 6 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
So i can still able to downgrade multiple ps3 right, and it work with ps3 slim 4.11?
I can't find the test point for the E3 linker on ps3devwiki. |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
|
|
