[nzie]

Originally Posted by playerkp420 I believe you can. I am gonna try to downgrade a nand model with it, and make a guide. Trying to research a little first, but there is no info on this thing. zoids looks like the only user on the internet to use it. Only problem I have is when I look at the pic for COK-001, on ps3devwiki, it says underneath "COK-001 EBUS testpoints (cannot use with hardware flashers)" Still trying to figure out what that means. Not sure exactly how many, but I believe you can use the pics on ps3devwiki, to find the points on your motherboard.

well im hoping another good downgrade guide from you

[osui818]

Playerkp420 could you make a tutorial for ps3 slim for the e3 linker? I can't find the test point. I have DYN-001/JTP-001

Thank you

[playerkp420]

Originally Posted by osui818 Playerkp420 could you make a tutorial for ps3 slim for the e3 linker? I can't find the test point. I have DYN-001/JTP-001 Thank you

Which motherboard do you have?



OR




I believe the points are like Progskeet. I just have to figure out which go where.

[v8s10]

Originally Posted by playerkp420 Only problem I have is when I look at the pic for COK-001, on ps3devwiki, it says underneath "COK-001 EBUS testpoints (cannot use with hardware flashers)" Still trying to figure out what that means.

That just means you can't use the test points to read/write the nands, you'll have to solder directly to the nands to read/write.
I have a COK-001 here that is toast so I desoldered the nands, and there are alternate solder points for all but about 7 of the 30 wires. Slightly easier to solder. I've been meaning to snap a few pics and post them up for anyone needing the alternate solder points.

[osui818]

Originally Posted by playerkp420 Which motherboard do you have? OR I believe the points are like Progskeet. I just have to figure out which go where.

I have both motherboard.

I dont understand the red color point, I know one is reset, but the other point I don't know where to connect with the e3 linker. And also the GND point (yellow) there is only 5 GND point on the e3 linker.

[playerkp420]

I see one red is reset and one red is ce. You only need to connect the 5 grounds no need to use all ground points on the board.

So all the green and yellow are pretty easy. Sbe goes to tristate.

But not sure where nwait, nwe, and noe?

Edit- actually i see nwe = red we, and noe = red oe.
************* [ - Post Merged - ] *************

Originally Posted by v8s10 That just means you can't use the test points to read/write the nands, you'll have to solder directly to the nands to read/write. I have a COK-001 here that is toast so I desoldered the nands, and there are alternate solder points for all but about 7 of the 30 wires. Slightly easier to solder. I've been meaning to snap a few pics and post them up for anyone needing the alternate solder points.

I would love to take a look at some pics of the alternate solder points. If you get a chance to upload some, i would appreciate it.
Thanks.

[osui818]

What about other point
BVCC, SBEE, VCC, NWAIT, NWE, CE, NOE?
Those point are on the e3 linker. Can you make a picture show where the point goes to?
I'm no pro, but I know u r

Edit:
Ok I found VCC, CE, OE, WE what is RY/BY?

[playerkp420]

Originally Posted by osui818 What about other point BVCC, SBEE, VCE, NWAIT, NWE, CE, NOE? Those point are on the e3 linker. Can you make a picture show where the point goes to? I'm no pro, but I know u r

bvcc = ? But I think I can find where. I remember seeing someone talk about bvcc.
vcc = yellow 3.3v vcc
sbe = red gp2 nor tristate
nwait = ? I think it is one of the 2 red ones left
nwe = red we
ce = red has (ce) next to it, like the red one that has (reset)
noe = red oe
sbce = I think goes to a point. Like in the fast dual boot guide, shows a pic of where to scratch out between point a and b, then solder wire from point a to sbce.
************* [ - Post Merged - ] *************
RY/BY ?
RST ?

BOTH RED?

[Haisenberg]

I brick my PS3, I did the welding procedure. then put multiple files "bkpps3.bin" that is not my model, and my backup file I made before the brick is corrupted

Now, how do I make a backup of my original ps3?

Excuse my English translator google, I'm from Brazil

please someone help me!

[Cj_Mc]

How many points you must solder on a NOR console ?