Noob with Progskeet ?'s - PS3Hax Network

dalowroller · 03-27-2012

So I picked up a 60gb Gen 1 from a buddy any he threw in a progskeet v1.1 with it but I'm slightly lost.

First the picture below is what all he gave me.

My question is first do I have everything I need to downgrade? (3.73)

From what I can gather I still need to solder even with the clip, does some one mind giving me a better description/image showing what needs to be soldered?

Also I've noticed while browsing that 2 clips can be attached and also there is add-on nands. I don't care about running dual nand but do I need 2 360 clips? And If I were to buy the other clip or the dual nands could I make this completly solder less or would I still need to solder?

Any Help would be greatly appreciated.

Chovoman · 03-28-2012

You need:

1. Progskeet programmed for solderless clip ( with INJECTUS )
2. 2 clips,not just one (ypu can also use just one,but you need to read 2 nand chips one by one)
3. And everything else you already have.

master737373 · 03-28-2012

And you also need a brain. Not trying to sound like a troll, but seriously, you need a brain.

Msparky83 · 04-04-2012

Is your console a dual NAND or NOR? I have fixed 10 ps3's with dual nand. I find that the CECHE-01 MG unit is my favorite because of the fact that nand1 is on the edge of the board, and I can use a small clamp to get the clip to stay in place. If your having trouble, PM me and I will help you out. Also, if you'd like me to fix it for you (i will only fix nand consoles at this time) again send me a PM with your interest. Cheers, an I hope it all works ouit for you in the end.

Chovoman · 04-05-2012

Originally Posted by Msparky83

Is your console a dual NAND or NOR? I have fixed 10 ps3's with dual nand. I find that the CECHE-01 MG unit is my favorite because of the fact that nand1 is on the edge of the board, and I can use a small clamp to get the clip to stay in place. If your having trouble, PM me and I will help you out. Also, if you'd like me to fix it for you (i will only fix nand consoles at this time) again send me a PM with your interest. Cheers, an I hope it all works ouit for you in the end.

I have a CECHG04 which went into YLOD while READING nand with x360 clip. I hear a lot of people have that problem.
Can you fix that problem? How can ps3 get an YLOD while reading nand? I know you can when writing the flashmbut reading???

Msparky83 · 04-08-2012

If all you did was truly "read" the nand, then you shouldnt have a ylod, unless maybe you took the heatsinks off and then attemted to power on your console...which could even cause you too short your system out completely,.

Explain to me fully step by step what you did and I will help troubleshoot. In the future only use progskeet for reading/writing dual nand consoles.

03-27-2012	#1
dalowroller Apprentice Join Date: Mar 2012 Posts: 1 Likes: 0 Liked 0 Times in 0 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Noob with Progskeet ?'s So I picked up a 60gb Gen 1 from a buddy any he threw in a progskeet v1.1 with it but I'm slightly lost. First the picture below is what all he gave me. My question is first do I have everything I need to downgrade? (3.73) From what I can gather I still need to solder even with the clip, does some one mind giving me a better description/image showing what needs to be soldered? Also I've noticed while browsing that 2 clips can be attached and also there is add-on nands. I don't care about running dual nand but do I need 2 360 clips? And If I were to buy the other clip or the dual nands could I make this completly solder less or would I still need to solder? Any Help would be greatly appreciated.

		PS3Hax Network - Playstation 3 Hacks and Mods > PS3Hax > PS3 \| Downgrading and Flashing
Noob with Progskeet ?'s

03-28-2012	#2
Chovoman Member Join Date: Jan 2012 Posts: 40 Likes: 5 Liked 1 Time in 1 Post Mentioned: 0 Post(s) Tagged: 0 Thread(s)	You need: 1. Progskeet programmed for solderless clip ( with INJECTUS ) 2. 2 clips,not just one (ypu can also use just one,but you need to read 2 nand chips one by one) 3. And everything else you already have.

03-28-2012	#3
master737373 Member Join Date: Mar 2012 Posts: 193 Likes: 11 Liked 72 Times in 47 Posts Mentioned: 22 Post(s) Tagged: 0 Thread(s)	And you also need a brain. Not trying to sound like a troll, but seriously, you need a brain.

04-04-2012	#4
Msparky83 Apprentice Join Date: Oct 2010 Location: nunya Posts: 25 Likes: 0 Liked 2 Times in 2 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Is your console a dual NAND or NOR? I have fixed 10 ps3's with dual nand. I find that the CECHE-01 MG unit is my favorite because of the fact that nand1 is on the edge of the board, and I can use a small clamp to get the clip to stay in place. If your having trouble, PM me and I will help you out. Also, if you'd like me to fix it for you (*i will only fix nand consoles at this time*) again send me a PM with your interest. Cheers, an I hope it all works ouit for you in the end.

04-08-2012	#6
Msparky83 Apprentice Join Date: Oct 2010 Location: nunya Posts: 25 Likes: 0 Liked 2 Times in 2 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	If all you did was truly "read" the nand, then you shouldnt have a ylod, unless maybe you took the heatsinks off and then attemted to power on your console...which could even cause you too short your system out completely,. Explain to me fully step by step what you did and I will help troubleshoot. In the future only use progskeet for reading/writing dual nand consoles.

User Name		Remember Me?
Password