[xtremegamer]

My PS3 Slim (CECH-2501A) turns on but no screen shows up. Its stays on. When I try to follow this http://www.ps3hax.net/showthread.php?t=30738 guide the downgrade file installs but the dongle doesn't light up. The e3 flasher log shows no errors. how do I fix this problem.

Important Information:
I have the E3 Flasher (Limited) installed. I soldered a wire from Tristate to SBE. Connected A to SBCE and cut the connection between A and B. The ps3 was working fine with cfw. I was trying to dual Boot with 4.11

I had the cfw switch up when I had cfw rogero 3.1. when I switched all 1-6 down and my harddrive it went to the "plug in controller screen"
I updated to 4.11 and now I am where I am. Please help


Thanks for your time

[MrTrader]

Dont know what to tell you...take it to shop
************* [ - Post Merged - ] *************
or call some game-master to fix it...

[xtremegamer]

Originally Posted by MrTrader Dont know what to tell you...take it to shop ************* [ - Post Merged - ] ************* or call some game-master to fix it...

will they even accept my ps3 considering I obviously modded my ps3. "Game-Master" if only there were any.

[domelec]

reflash the patched file back to nor
if u dont have a patched and used the e3downgrade.bin then either get the original patched or try to redo the downgrade steps
excluding the making a backup

[xtremegamer]

Originally Posted by domelec reflash the patched file back to nor if u dont have a patched and used the e3downgrade.bin then either get the original patched or try to redo the downgrade steps excluding the making a backup

Thanks for reply. I will this in a bit and see what happens

[tjhooker73]

Originally Posted by xtremegamer My PS3 Slim (CECH-2501A) turns on but no screen shows up. Its stays on. When I try to follow this http://www.ps3hax.net/showthread.php?t=30738 guide the downgrade file installs but the dongle doesn't light up. The e3 flasher log shows no errors. how do I fix this problem. Important Information: I have the E3 Flasher (Limited) installed. I soldered a wire from Tristate to SBE. Connected A to SBCE and cut the connection between A and B. The ps3 was working fine with cfw. I was trying to dual Boot with 4.11 I had the cfw switch up when I had cfw rogero 3.1. when I switched all 1-6 down and my harddrive it went to the "plug in controller screen" I updated to 4.11 and now I am where I am. Please help Thanks for your time

Should have installed OFW 3.55 before updating, there is your problem, if you don't have a nor back up you are SOL

[xtremegamer]

Originally Posted by tjhooker73 Should have installed OFW 3.55 before updating, there is your problem, if you don't have a nor back up you are SOL

I only have a 4.11 nor backup. can I still fix my ps3? I sucessfully unbricked my ps3 before.

[tjhooker73]

Originally Posted by xtremegamer I only have a 4.11 nor backup. can I still fix my ps3? I sucessfully unbricked my ps3 before.

If its a good dump then yes you can recover.

[xtremegamer]

Originally Posted by tjhooker73 If its a good dump then yes you can recover.

It is a good one since I used it to unbrick ps3 in the past. do you know of a tutorial I can follow because when I get to the downgrading step theirs no power coming from the usb meaning my e3 flasher wont do its magic...

Thanks for a reply