[joemuscles]

Originally Posted by hellsing9 The best i can find..for the moment. Check this = click The tristate it's to debrick:

The Upload was no good? you couldn't see everything still? I'v done a lot of reading on E3 installing ,but for my model I don't think there is a a/b scratch out for dual boot just unsoldering the resistor near the nor chip. I thought nor tristate was just installed in case of brick?

[hellsing9]

Nor tristate it's installed in case you brick, so you can debrick. (Also for dual boot but in your board is kinda confusing)
Im seeing the pics right now, the upload was awesome use this site from now on don't do attachments.

Im trying to figure out what is that resistor. xD

Check this out it's a .pdf = click

Sorry if im spamming you, let me know.

This is tristate:







Here says : place some tape where you soldered to avoid short circuit.

[joemuscles]

Originally Posted by hellsing9 Nor tristate it's installed in case you brick, so you can debrick. (Also for dual boot but in your board is kinda confusing) Im seeing the pics right now, the upload was awesome use this site from now on don't do attachments. Im trying to figure out what is that resistor. xD Check this out it's a .pdf = click Sorry if im spamming you, let me know.

Spam the sh*t out of me , I'm glad the upload was good and your helping me out. lol
thanks

[hellsing9]

Now you have the dual boot option:

Part of the weilding wire for FAST dual boot
Now you have to solder point SBCE on the motherboard "white wire, acording to your card be cautious"
If you want JSD-001 use the images below as reference.



Point welding SBCE top
Cooper bridge between two solder balls (as you can) *rougly translated*



Explanation: between the two solder balls there is a wire that it's built into the motherboard (original) we must try to cut it out, either with a cutter or sharp knife BE CAREFUL and cut very small bridge.
If you find this too risky for your taste don't no keep with dual boot half (2 MICRO SD CARDS)

[playerkp420]

Originally Posted by joemuscles Spam the sh*t out of me , I'm glad the upload was good and your helping me out. lol thanks

You got the pick of where the clip goes from @hellsing9 .

Here is the pic of the other side of the board, with labels.

If you are going to fast dual boot, you need to solder a wire from sbe on the e3 clip ribbon to nor tristate.
Also scratch a track (NOT TOO DEEP) between point a and b.
And solder a wire from sbce on e3 clip ribbon to point a.

Remember only do this if you are going to fast dual boot.

[joemuscles]

TDCroPower2 posted a mod for dual boot ver-001 boards ect here at this site

http://www.ps3hax.net/showthread.php?t=33143&page=7

show some good pics of it, That's why i edited my pics to see if i was right on the locations for the dual boot and E3 Flasher. let me know .

thanks

[hellsing9]

Here @playerkp420 saved your day. Read what he said

[joemuscles]

Thanks hellsing, did you examine my pics? We established the nor chip location for my board, how about the resistor and the nor tristate location on the other pic?

[playerkp420]

Originally Posted by joemuscles Thanks hellsing, did you examine my pics? We established the nor chip location for my board, how about the resistor and the nor tristate location on the other pic?

I see what you mean now. But I don't see any pics on that page you linked.

[joemuscles]

Thanks
playerkp420 for the reply as well. Those pics are from a different type of motherboard, the a/b scratch out method to dual-boot is not for the DIA-001 boards correct? I only think that resistor mod is.
************* [ - Post Merged - ] *************

Originally Posted by playerkp420 I see what you mean now. But I don't see any pics on that page you linked.

http://i.imgur.com/PYDwr.jpg

http://i.imgur.com/0sN36.jpg

these links to my pics work? let me know