[rot]

Do i need to turn the ps3 on to dump the nand or do i just plug in the power cable?

[v8s10]

Needs to be on, or power nands externally, or through progskeet.

I always turn ps3 on for dumping nands, but i solder instead of using the nandclip.

[Freesty]

nothing, if you use 360 clip you dont need power till you finish with flashing and composing console.
************* [ - Post Merged - ] *************
v8s10 do you have some successful downgraded nand console with progskeet? and if can you put some picture?
tell how you prepare progskeet and yust in few steps tell how you do that?
i ask because we have allot of tutorials but i have a headache of tutorials for one thing on different sites.

[rot]

anyone want to take a look at my first dump? top of the board. or are there any programs to auto verify?

http://www.mediafire.com/?xizc8g9bnk0xce7
************* [ - Post Merged - ] *************
anyone want to take a look at my first dump? top of the board. or are there any programs to auto verify?

http://www.mediafire.com/?xizc8g9bnk0xce7

[v8s10]

Originally Posted by rot anyone want to take a look at my first dump? top of the board. or are there any programs to auto verify?

Can't tell if its a good dump from just one, you need to dump both then run through flow rebuuilder. I'm sure its bad though, it should be 132 MB not 128 MB. What are you using for settings in winskeet?

Originally Posted by Freesty v8s10 do you have some successful downgraded nand console with progskeet? and if can you put some picture? tell how you prepare progskeet and yust in few steps tell how you do that? i ask because we have allot of tutorials but i have a headache of tutorials for one thing on different sites.

Yes I have downgraded a few, also bricked a few that were ylod repairs, so no loss.

I solder the connections for the nands because i bricked one ps3 with a bad clip connection. I use header pins soldered to the progskeet, like this:
http://www.progskeet.com/forum/viewtopic.php?f=3&t=3749

[rot]

Originally Posted by v8s10 Can't tell if its a good dump from just one, you need to dump both then run through flow rebuuilder. I'm sure its bad though, it should be 132 MB not 128 MB. What are you using for settings in winskeet? Yes I have downgraded a few, also bricked a few that were ylod repairs, so no loss. I solder the connections for the nands because i bricked one ps3 with a bad clip connection. I use header pins soldered to the progskeet, like this: http://www.progskeet.com/forum/viewtopic.php?f=3&t=3749

i just hit the auto button.

and it sets it at
page per blocks:64
block count:1024
with big block checked.

and why would it be 132 256/2 = 128

[v8s10]

Originally Posted by rot i just hit the auto button. and it sets it at page per blocks:64 block count:1024 with big block checked. and why would it be 132 256/2 = 128

Make sure you have raw checked too. I know 132 MB doesn't make sense, but when it gets interleaved with flow rebuilder, you get a single 256 MB file. Check this page 1/3 of the way down....says you should get 132 MB
http://www.ps3devwiki.com/wiki/Hardw..._low.2Fhigh.3F

Actually most of what you need should be there on a few pages.

[rot]

Originally Posted by v8s10 Make sure you have raw checked too. I know 132 MB doesn't make sense, but when it gets interleaved with flow rebuilder, you get a single 256 MB file. Check this page 1/3 of the way down....says you should get 132 MB http://www.ps3devwiki.com/wiki/Hardw..._low.2Fhigh.3F Actually most of what you need should be there on a few pages.

ugh dam wiki is down

what speed should i use says should take 3 mins but its taking me about 10

[v8s10]

Originally Posted by rot ugh dam wiki is down what speed should i use says should take 3 mins but its taking me about 10

If using the newest winskeet just select the dual nand preset and leave the cycle period at default (125ns) and read delay at 50 (also default).
I don't remember how long it takes to dump, but i can check if it helps.

[rot]

Originally Posted by v8s10 If using the newest winskeet just select the dual nand preset and leave the cycle period at default (125ns) and read delay at 50 (also default). I don't remember how long it takes to dump, but i can check if it helps.

im using the 111205.