[arkano]

My PS3 is briked. I soldered the NOR Tristate to SBE and the point A to SCBE. Afther that, my PS3 is no video signal and leds of Wireless or HD don`t blink. I did all the procedures to restore the PS3. At E3 Flasher UDDDDD with my backup (is good) and start. No video signal and the leds of HD video or wireless don`t bilnk yet.
I put the downgread.bin and E3 FLASHER DDDDDU and start. No video signal and leds of HD or wireless don`t blink yet. After that, i put the dongle and the USB is dead, the dongle won`t start.
Can someone help me?

[MJ999]

Did you flash your ps3 ?

You verified your dumps? Just upload your dump

[AsSiTcH]

Originally Posted by arkano My PS3 is briked. I soldered the NOR Tristate to SBE and the point A to SCBE. Afther that, my PS3 is no video signal and leds of Wireless or HD don`t blink. I did all the procedures to restore the PS3. At E3 Flasher UDDDDD with my backup (is good) and start. No video signal and the leds of HD video or wireless don`t bilnk yet. I put the downgread.bin and E3 FLASHER DDDDDU and start. No video signal and leds of HD or wireless don`t blink yet. After that, i put the dongle and the USB is dead, the dongle won`t start. Can someone help me?

Nice use of spellcheck.

[slaughter]

Dude he's looking for help and all you can do is criticize his spelling. He's more worried about his ps3 then a stupid spell check to make asses like you happy.

[AsSiTcH]

Originally Posted by slaughter Dude he's looking for help and all you can do is criticize his spelling. He's more worried about his ps3 then a stupid spell check to make asses like you happy.

If he can't care enough to spell correctly, it is no wonder is ***0red his console.

[Bigbones87]

@arkano you seem to have done mostly right. Try this. Put your bios on the sd card and put switch 1 up, then hit start. Dont turn the ps3 off. When all the blue lights are done lighting up, take the sd card and put the downgrade.bin on there. Keep your bios on there with the downgrade.bin. Then put switches down except 6 up, then hit the red reset button on the flasher and then hit start. Then when it is done, turn the ps3 off by holding the power button down. Then turn it back in it should say plug in ps3 controller. DONT, turn it off by pulling power or switching the switch in back. Then put the fsm dongle in the right USB port and then do the power eject. It should turn on and then off by itself. If your USB ports don't seem to be active or have power, then unplug the e3 ribbon cable from the e3 flasher motherboard. This should restore power to the USB ports. If it fixes the USB ports, then go ahead do the fsm, then USB with step 1 lvl2 diag and rogero.pup, then USB with step 2 lvl2 diag, then success.
Before any of this, you should make sure your dumps are good.

[arkano]

Originally Posted by Bigbones87 @arkano you seem to have done mostly right. Try this. Put your bios on the sd card and put switch 1 up, then hit start. Dont turn the ps3 off. When all the blue lights are done lighting up, take the sd card and put the downgrade.bin on there. Keep your bios on there with the downgrade.bin. Then put switches down except 6 up, then hit the red reset button on the flasher and then hit start. Then when it is done, turn the ps3 off by holding the power button down. Then turn it back in it should say plug in ps3 controller. DONT, turn it off by pulling power or switching the switch in back. Then put the fsm dongle in the right USB port and then do the power eject. It should turn on and then off by itself. If your USB ports don't seem to be active or have power, then unplug the e3 ribbon cable from the e3 flasher motherboard. This should restore power to the USB ports. If it fixes the USB ports, then go ahead do the fsm, then USB with step 1 lvl2 diag and rogero.pup, then USB with step 2 lvl2 diag, then success. Before any of this, you should make sure your dumps are good.

My dumps it`s ok. I will try this. THX

sorry for my bad english, i'am brazilian

[Bigbones87]

It's cool man. I don't care how bad your English is or where you are from....this ps3hax man. We accept all mofos. Hope we get through your issue and get your ps3 back up and running like a healthy little champ.

[arkano]

Originally Posted by Bigbones87 @arkano you seem to have done mostly right. Try this. Put your bios on the sd card and put switch 1 up, then hit start. Dont turn the ps3 off. When all the blue lights are done lighting up, take the sd card and put the downgrade.bin on there. Keep your bios on there with the downgrade.bin. Then put switches down except 6 up, then hit the red reset button on the flasher and then hit start. Then when it is done, turn the ps3 off by holding the power button down. Then turn it back in it should say plug in ps3 controller. DONT, turn it off by pulling power or switching the switch in back. Then put the fsm dongle in the right USB port and then do the power eject. It should turn on and then off by itself. If your USB ports don't seem to be active or have power, then unplug the e3 ribbon cable from the e3 flasher motherboard. This should restore power to the USB ports. If it fixes the USB ports, then go ahead do the fsm, then USB with step 1 lvl2 diag and rogero.pup, then USB with step 2 lvl2 diag, then success. Before any of this, you should make sure your dumps are good.

I Stop after downgrade.bin. I can`t see the plug in ps3 controller. My tv is no signal. I use HDMI.

What i can do to fix that. I have done the 2 solders. One to the Nor tristate to SBE and Point A to SCBE.

My PS3 in no video.
************* [ - Post Merged - ] *************
I Use the "firmware" of dual boot (2012.01.05 update) on e3 flasher

[Bigbones87]

@arkano Continue with the process. When you turn it back on, if doesn't show you the connect ps controller screen, just switch it off by the switch on back, then continue with the fsm dongle, step 1 files, step2 file. Then you should get it working.