[baileyscream]

Originally Posted by smalltylynch so flashed ps3 and then disconnected every thing it booted for a second and then turned of now it wont boot at all so i connect my progskeet and tried doing the unbrick but when i dump CFI it says "CFI is invalid (does not begin with "QRY")" is my ps3 bricked?

ok @playerkp420 is the best to ask about the pspjig as i have never got this to work.

as for the brick fix.

connect the progskeet and make sure every wire is attached correctly.
connect 3.3v (may also be vcc on the diagrams) from prog to vcc (may be nor vcc) on ps3

plug in progskeet

progskeet should be detected by the pc

click (dump cfi) if this fail's then your wiring is wrong

click dump (to compare you dump) if you get a bad dump then check your wiring

wiring at this point is what all faults are created by
that includes the usb cable. the usb may work with other devices but the progskeet is super sensitive so try another usb cable (the shorter the better)
************* [ - Post Merged - ] *************

Originally Posted by djbaaz at "Finishing the down grade in service mode" I got the same screen as in the picture, but I connected the ps3 controller and got another message that harddrive is "something" and upgrade to 3.70 and reformat the harddrive" I afterward unplugged the powersource ( not the cable. I open up my ps3 and unplugged the entire powercurcit ) and now there is no power at all. What can be done? Plzzzzz help.... using the e3 flasher limitied

why have you removed the power supply?
put it back and it will boot.
no power >>>>> no boot

[Sarah1331]

Thanks dude I usually get on at people for poo soldering aswell advice taken I'll start over thanks

[baileyscream]

Originally Posted by Sarah1331 Ok thanks again Rewired again all ok I can post pics If you want With r7 open and console plugged in I get CFI I have fc the one I originally got when I dumped the console and got 8 good dumps and there the same With r7 and console not plugged in I get doesn't start with qry can you try this step with a different usb cable. its as though there is not enough power getting to the NOR to power it With r7 open and pluged in I flash and it adds lots of fffffffff (I read it back to see what just written) the ffff's is due to bad wiring there "fail's" / "corrupted sections" created by incorrect wiring / dead solder / shorts / damaged track / faulty usb cable With R7 closed It just hangs forever not enough power to the NOR change usb cable When I erase with r7 open and plugged in it comes back as nothing but ff ff ff ff When I erase with r7 closed it just hangs (even if I make two cups of tea) When I flash it's like it's not flashing all the 00 they stay as ff's I have tested for shorts all over with multimeter and scopes When I flash on static timing it hangs but when I read Nor where it hung it flashed correct to that point

ok try a new usb cable
like this one for the extra power line
http://www.ebay.co.uk/itm/USB-DUAL-P...item2c67353a2a

or one thats about 10cm 4inch long
http://www.ebay.co.uk/itm/USB-2-0-A-...item5639213c99
************* [ - Post Merged - ] *************

Originally Posted by Decoy is this the multimeter youre meaning? no this is a diagram but the thing worrying me is that they sent me message saying: so i dont know if it will be compitable..

this is a multimeter
http://www.ebay.co.uk/itm/NEW-DT830B...item256c6a120b

there is no diagram for the 1.2 yet so when they have one saying what solder pad on the progskeet 1.2 goes where then you can wire that header board propperly
************* [ - Post Merged - ] *************

Originally Posted by Sarah1331 Thanks dude I usually get on at people for poo soldering aswell advice taken I'll start over thanks

no no no post 361 wasn't aimed at you the poste 363 is for you.

[Sarah1331]

Lol thanks again

[Decoy]

@baileyscream ah I understand now , I'll get a multimeter later , but now I'll search for the clip I showed you earlier , my concern was if it wasn't gonna fit/work on the new progskeet .

[baileyscream]

Originally Posted by Decoy @baileyscream ah I understand now , I'll get a multimeter later , but now I'll search for the clip I showed you earlier , my concern was if it wasn't gonna fit/work on the new progskeet .

what you showed me was a pin headder board
it comes with the NOR clip

[Decoy]

Yes it comes with that nor thingy , that's the only way to get it .. , ill search for it now .

[baileyscream]

Originally Posted by Decoy Yes it comes with that nor thingy , that's the only way to get it .. , ill search for it now .

you could attach the NOR clip to the NOR

then attach the pin headder board to the clip

then trace the pin heads to the test points on the ps3

then using jumper wires attach the pin headder to the progskeet 1.2's solder points

like how i did the TEENSY++ (see the guide)

i think i will do this for the progskeet NOR guide as it will be easer to leave the pin headder free then to remove the trace on the NOR clip

[Decoy]

Oh so you have it already , didn't know . But I read somewhere that if you use the nor clip on different ps3s it will be damage , but I don't care about the clip , I want the header board the most , I'll see your guide first and then decide what way to use . , Any news about it ? The 1.2 guide ?

[djbaaz]

Originally Posted by baileyscream ok @playerkp420 is the best to ask about the pspjig as i have never got this to work. as for the brick fix. connect the progskeet and make sure every wire is attached correctly. connect 3.3v (may also be vcc on the diagrams) from prog to vcc (may be nor vcc) on ps3 plug in progskeet progskeet should be detected by the pc click (dump cfi) if this fail's then your wiring is wrong click dump (to compare you dump) if you get a bad dump then check your wiring wiring at this point is what all faults are created by that includes the usb cable. the usb may work with other devices but the progskeet is super sensitive so try another usb cable (the shorter the better) ************* [ - Post Merged - ] ************* why have you removed the power supply? put it back and it will boot. no power >>>>> no boot

Well, I have connected the powersupply back again, it was after that ps3 did not got any power.

ALSO, when I get it to work, then I want to know what I should do with the Standard PS Jailbreak dongle, something with some files to add? hope any1 can answer it....thx in advance