[Abkarino]

Originally Posted by butnut @Abkarino What kind of ps3 did you convert phat or slim? If it was a phat was it nand or nor? Also was your ps3 qa flagged before you converted? And what cex firmware were you on when you converted?

It was a slim console and QA flag was enabled before using this tool.
BTW: today i had tested package installation but i can not install any package file.
It gives me an error code 0x80029567 that mean that i'm trying to install retail pkg under debug console even if its a debug pkg.
So i had dumped my NOR again then compared my eEID before and after conversion and i found it the same
Even if Debug firmware was installed without any error and i can use the debug settings also.
So after that i entered the FSM and installed Rogero CFW for CEX and it worked like a charm.
So i think this method need more research to enhance it since its safer than normal hardware flasher.

Originally Posted by haz367 @Abkarino can u test a blu-ray movie for us to see if it's running?..thx!

I'm so sorry i does not have any BD Movies

[TheWhiteTyger]

Originally Posted by evilsperm its supposed to pass then fail because it just loops

I'm gonna get bashed for this, but someone needs to say it.

Would you care to share some more info?

I'm not speaking for everyone here, but what's the point of you showing up and mentioning something small like this and then not share anything else? If this is not your intention, just ignore me. Prove me wrong, and I will never have to question you again.

BTW, IF this offends you, your too egotistical and have no place in a "public" scene that is a community when you have knowledge and refuse to share until someone else "leaks" the methods in question and then a money-making scheme is now worthless.

All I am saying is if you want to help the "scene" then help us, don't feed us tidbits of info and act like you have all the know-how and withhold information that could progress the scene along, if that is what you are doing.

With all due respect, we don't need another "Math" around here. Just saying, schitt or get off the pot. Either help, or leave. This scene is already screwed up enough and has had too many disappointments to count.

Let the bashing begin, I just hope I am proved wrong.

[haz367]

ouch..kabam...anyway thx for confirm @Abkarino , if u check the FSM manual it's maybe like haxxxen already mentioned..the ID needs manual edit(yellow star) ...thx again for update so we do not waste our time more info is needed here i guess, nontheless sharing is caring..for that..we thank u guys

and itwould be great if BD movies worked with "full" convert of all eid's, also there's a rar "fixps3flash" with a lv2diag.self in it, it's supposed to be used for something in the cex2dex area?!... can't find info on this one....my bet is full convert do have bd playback and doesn't show that "red" error/warning in tm about not a "supported" model(DEV) just thinking out loud could be bull what i'm posting..in this scene it's alot guessing anyway hehe

maybe that leak was for dex2cex

[butnut]

Originally Posted by evilsperm its supposed to pass then fail because it just loops

Ok thanks for clearing that up.

Well I just downgraded to 3.55dex and and flashed my request idps from my cex dump. It said pass then fail just like before. so I exit service mode and try to install kmeaw but all cex pups are still black/greyed out in the list, and dex pups are white. I suppose its possible this thing only does cex-dex and not dex-cex, but if that is the case then If I dump my flash I should see my eid5 say 82 and not 84. dumping flash now.

Edit: okay the dump is done and

BOTH OF MY IDPS'S SAY 84!!!!!???? This ps3 is not qa flagged, I am running dex firmware, I can install dex firmware from the xmb, I cannot install cex firmware from the xmb, real game discs play, and all of this with a cex flash??? The hell... ?


@TheWhiteTyger

Look man Evilsperm is helping okay, I would not have tried this program again and I may have never known if I was using it properly, but now that I do thanks to him, I have decided to take the next steps and see where it leads and it may lead nowhere but at least I am doing something. Rather than cry about how devs never share, why don't you try to learn for yourself if this info is that important to you, even if you fail its okay just crawl out of the frigging high chair and grab a spoon already, you might get more on you than in you but at least you will be trying to do something for yourself.

[haz367]

@butnut :

i'm about to try to...one small thing, it sais to have PS3 on IP 192.168.0.100 before trigger FSM, all good but when i boot into FSM every time the network conn gets reset to "auto" screwing up the conn between pc-ps3

is it just setting IP manual on 355cex, power off, trigger FSM with dongle but not boot yet?! , insert usb with convert_console files on root, then run objsuite and quikly turn on PS3..thx for any help on the ip thingy..

[diesel701]

Originally Posted by butnut Ok thanks for clearing that up. Well I just downgraded to 3.55dex and and flashed my request idps from my cex dump. It said pass then fail just like before. so I exit service mode and try to install kmeaw but all cex pups are still black/greyed out in the list, and dex pups are white. I suppose its possible this thing only does cex-dex and not dex-cex, but if that is the case then If I dump my flash I should see my eid5 say 82 and not 84. dumping flash now.

So, it would be awesome if you can extract the request_idps from the dex dump and then from the cex dump. And compare them.

[JonahUK]

Originally Posted by haz367 @butnut : i'm about to try to...one small thing, it sais to have PS3 on IP 192.168.0.100 before trigger FSM, all good but when i boot into FSM every time the network conn gets reset to "auto" screwing up the conn between pc-ps3 is it just setting IP manual on 355cex, power off, trigger FSM with dongle but not boot yet?! , insert usb with convert_console files on root, then run objsuite and quikly turn on PS3..thx for any help on the ip thingy..

Try allocating a static IP from the PC so the PS3 can't use any other IP?

[haz367]

the weird part is that the created request.idps.txt shows CEX TargetID, then objective suite should convert along the way? all the info the original guide/middle-man needed are the txt files from "get per console data" he then send u a request.idps.txt back, was this file also with CEX targetid or already DEX 82?

8. Get ALL these txt files from your temp directory and send them to the author (me) with informations about your playstation 3 model (FAT/SLIM, CECH* model) ** PART 2 ** 9. You should recieve from the author (Yeah me again) a file called request_idps.txt 10. Extract ObjectiveSuites-SetIdps on your pc. 11. Put the request_idps.txt in your temp folder (MAKE EXTRA SURE IT'S THERE OR YOU WILL BRICK)

these 2 can be dumped from the flash as seen on this TOOL (req.idps.txt&per console txt files, same as STEP1 -- ObjectiveSuites-GetData


atleast after converting, the new dump flash should contain DEX target ID correct and not original 84/85 etc...thats just weird...



edit: @JonahUK

nvm....thx for reply, it was the first thing afterall( PC ip 192.168.0.100) cheers @butnut

[butnut]

Originally Posted by haz367 @butnut : i'm about to try to...one small thing, it sais to have PS3 on IP 192.168.0.100 before trigger FSM, all good but when i boot into FSM every time the network conn gets reset to "auto" screwing up the conn between pc-ps3 is it just setting IP manual on 355cex, power off, trigger FSM with dongle but not boot yet?! , insert usb with convert_console files on root, then run objsuite and quikly turn on PS3..thx for any help on the ip thingy..

You set your pc at 192.168.0.100
and your pc's hostmask to 255.255.255.0
All other fields can be left blank.

You don't need to change any settings on your ps3.

[diesel701]

Originally Posted by haz367 the weird part is that the created request.idps.txt shows CEX TargetID, then objective suite should convert along the way? all the info the original guide/middle-man needed are the txt files from "get per console data" he then send u a request.idps.txt back, was this file also with CEX targetid or already DEX 82? these 2 can be dumped from the flash as seen on this TOOL (req.idps.txt&per console txt files, same as STEP1 -- ObjectiveSuites-GetData atleast after converting, the new dump flash should contain DEX target ID correct and not original 84/85 etc...thats just weird...

I think that we must change manually in the request_idps.
To make sure of this, we must have a dump of the console after the process and see if the request_idps changed or it's the same as in the beginning of the process.