[TUT] Fast Dual Boot (e3 flasher) - Page 16 - PS3Hax Network

hani90 · 09-18-2012

what happens if you remove this resistor and boot the ps3 without connecting it to e3 flexcable??

geeklogik · 10-19-2012

after soldering and cutting link between a and b
my ps3 barely stays on for 5 seconds
i have checked a and b is cut properly with a multimeter-no beep
i have checked point A beeps when finding the right clip on the e3 ribbon
same as the nor tristate and the sbe

geeklogik · 10-20-2012

BUmp need help please, guys !

windrider42 · 10-20-2012

Originally Posted by geeklogik

after soldering and cutting link between a and b
my ps3 barely stays on for 5 seconds
i have checked a and b is cut properly with a multimeter-no beep
i have checked point A beeps when finding the right clip on the e3 ribbon
same as the nor tristate and the sbe

You may have better luck to have posted in the Downgrade section or the help section.

geeklogik · 10-23-2012

Originally Posted by windrider42

You may have better luck to have posted in the Downgrade section or the help section.

i had a solder splatter , on the ps3 mobo connecting two capictors, i sneezed while soldering lol.

all good.!

kman82 · 10-23-2012

Bahaha yeah u don't wanna be doing that whilst soldering!

geeklogik · 10-27-2012

Originally Posted by kman82

Bahaha yeah u don't wanna be doing that whilst soldering!

need some help up to step 4 . if i start ps3 with cfw switch up, it goes of in 30 secs, with ofw switch it stays on, no screen?, idono? and for the first few steps must i use the e3_downgrade bin as it never works for me i use a manually flashed backup with flash fun

? thanks!:flowers

is it necessary to put cfw switch up at step 4?

Fgroia · 11-02-2012

is it possible to check the motherboard without opening the ps3?

MJ999 · 11-02-2012

Originally Posted by Fgroia

is it possible to check the motherboard without opening the ps3?

check your ps3 model ( CECHx-xxxx ) and identify it from this list

http://www.ps3devwiki.com/wiki/SKU_Models

Alias1271 · 03-16-2013

Hi,

I have a CECHM03 model with a DIA-001 board.

1. Just to be clear as I can't zoom in on the solder wire image, I should solder the left side of the resistor. Leaving the NOR side open circuit?
2. If I solder the wire to SCBE(flexicable), can I do normal process for a single CFW installation first and deal will the dual boot procedure later?

Thanks in advance

10-23-2012	#156
kman82 Member Join Date: Nov 2011 Posts: 91 Likes: 0 Liked 11 Times in 5 Posts Mentioned: 7 Post(s) Tagged: 0 Thread(s)	Bahaha yeah u don't wanna be doing that whilst soldering! __________________ HOW DO YOU LIKE DEM APPLES

		PS3Hax Network - Playstation 3 Hacks and Mods > PS3Hax > PS3 \| Downgrading and Flashing
[TUT] Fast Dual Boot (e3 flasher)

09-18-2012	#151
hani90 Apprentice Join Date: Sep 2012 Posts: 1 Likes: 0 Liked 0 Times in 0 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	what happens if you remove this resistor and boot the ps3 without connecting it to e3 flexcable??

10-19-2012	#152
geeklogik Member Join Date: Oct 2012 Posts: 143 Likes: 48 Liked 18 Times in 14 Posts Mentioned: 20 Post(s) Tagged: 0 Thread(s)	after soldering and cutting link between a and b my ps3 barely stays on for 5 seconds i have checked a and b is cut properly with a multimeter-no beep i have checked point A beeps when finding the right clip on the e3 ribbon same as the nor tristate and the sbe

10-20-2012	#153
geeklogik Member Join Date: Oct 2012 Posts: 143 Likes: 48 Liked 18 Times in 14 Posts Mentioned: 20 Post(s) Tagged: 0 Thread(s)	BUmp need help please, guys !

11-02-2012	#158
Fgroia Member Join Date: May 2007 Posts: 85 Likes: 9 Liked 4 Times in 2 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	is it possible to check the motherboard without opening the ps3?

03-16-2013	#160
Alias1271 Apprentice Join Date: Feb 2013 Posts: 3 Likes: 0 Liked 0 Times in 0 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Hi, I have a CECHM03 model with a DIA-001 board. 1. Just to be clear as I can't zoom in on the solder wire image, I should solder the left side of the resistor. Leaving the NOR side open circuit? 2. If I solder the wire to SCBE(flexicable), can I do normal process for a single CFW installation first and deal will the dual boot procedure later? Thanks in advance

User Name		Remember Me?
Password