[kylum]

Originally Posted by fudd69 Hi. I still get rlod!!! why is it?? I' ve done exactely as you said: soldered wire from tristate point on PS3 to SBE point on E3 clip; connected E3 flasher to PS3. Boot ... still get rlod!! What have I done wrong?! I add some pictures of my soldering. thanks for your help

You cut off to much shielding off the wire at the tristate. It's really close to a resistor I hope that it didn't cause a short. You should be ok but just FYI

You are putting the e3 in flashfun mode. Switches should b set first up and rest of them down.

[w0313]

hi guys, my BD Drive is experiencing something wrong. i cant play games with or discless on Kmeaw a while ago,it beeped and dead. so i change the firmware to OFW 3.55 from Kmeaw via RecMod and then i insert the GRID Original BD, i can play it for 3 hours without beeps of death. i took a rest for a half an hour then start the console again and play GRID, guess what. the BD Drive cant read the disc and i should insert another BD on it but the result is the same. i've done Restore File System, Restore PS3 System, just no good result at all. should i remarry the blueray drive?or i just convert it to DEX4.21? thanks for everything....

[Sharon4941]

the title name is awesome!

[windrider42]

Originally Posted by w0313 hi guys, my BD Drive is experiencing something wrong. i cant play games with or discless on Kmeaw a while ago,it beeped and dead. so i change the firmware to OFW 3.55 from Kmeaw via RecMod and then i insert the GRID Original BD, i can play it for 3 hours without beeps of death. i took a rest for a half an hour then start the console again and play GRID, guess what. the BD Drive cant read the disc and i should insert another BD on it but the result is the same. i've done Restore File System, Restore PS3 System, just no good result at all. should i remarry the blueray drive?or i just convert it to DEX4.21? thanks for everything....

Read_ Ps3 doesn't read Optical media

http://www.ifixit.com/Wiki/PlayStati...roubleshooting

[3absiso]

@baileyscream
Is the first PS3 CECHA with 1.00 OFW can be downgraded.
i read on the PS3WikiDev that making a dump was note completed.
just to make sure?
i had one in my hand, and it is my first Nand Downgrade. but i think it can not be downgraded as in the PS3WikiDev say.

[baileyscream]

Originally Posted by 3absiso @baileyscream Is the first PS3 CECHA with 1.00 OFW can be downgraded. i read on the PS3WikiDev that making a dump was note completed. just to make sure? i had one in my hand, and it is my first Nand Downgrade. but i think it can not be downgraded as in the PS3WikiDev say.

that part of the wiki page was a reference for the devs.
the progskeet was being developed and they needed to see what it could do and couldnt.

it was posted incompleate but it is usefull.

the 1.00 f/w was never extracted fully. but the ps3 can be downgraded (not from 1.00 though )

if you have one on 1.00f/w and you can extract a dump then post it over there i am sure the devs will apreciate being able to look at a full dump

[elzincho]

for the teensy++ do you need to have people check your dumps? or is that optional. also for the cech-25xx it sais if certain values are not the same its not downgradeable, if the ps3 passes the minimum version check will i run into that problem?

[Sarah1331]

Me again

Do I have to change the bitstream of the progskeet to read a NAND or only If I get a clip ??

I have currentley read and downgraded 4 nor but run into a NAND I want to do tomorow

If I update to the latest bitstream can I still use my wire method for not and wire direct to nands this is what I would like

Also is there anyway to identify what my progskeet currentley has on it

[baileyscream]

Originally Posted by elzincho for the teensy++ do you need to have people check your dumps? or is that optional. also for the cech-25xx it sais if certain values are not the same its not downgradeable, if the ps3 passes the minimum version check will i run into that problem?

get your dump checked by others. its allways good to have someone double check it for you.

if it passes min ver check then you can downgrade.
that part is in the guide as a double check so dont skip it
************* [ - Post Merged - ] *************

Originally Posted by Sarah1331 Me again Do I have to change the bitstream of the progskeet to read a NAND or only If I get a clip ?? I have currentley read and downgraded 4 nor but run into a NAND I want to do tomorow If I update to the latest bitstream can I still use my wire method for not and wire direct to nands this is what I would like Also is there anyway to identify what my progskeet currentley has on it

the bitstream that is allready on it will allow:
reading from
nor clip
nor test points via soldering
nand direct solder via wire
(solder direct to the legs of the nand chip as the test points do not link direct to the nand chip)

the update bitstream is for:-
nand clip only

you can flash back and forth between the bitstreams as you require
(both bitstreams are in the nand guide pack)

as your from the xbox scene you may allready know if there are any qsb's for the nand (any that connect direct to the chip itself?)
if you do you may be able to use them.

also if you do know of any please post a link

[Sarah1331]

I don't know of a direct qsb for the NAND but I wonder if I put the tsop on a Xbox if I can read it with a NAND x what do you think to this ??

Failing that am confident to direct wire or lift the tsop and direct wire

And thanks again

Edit I'll make some thing you will be proud of to read nands without the expensive clip