[baileyscream]

Originally Posted by Kazrael21 Well my progskeet is all programmed and ready to go, now i just need to know how the new version 1.2 is connected and soldered to the ps3.

i know we went through this in p/m but for anyone else reading this.
the progskeet user guide has the solder pads on the progskeet 1.2 mapped out except for the address lines so it is still usless to use without these
this is for nor btw
if progskeet get back to you please post the solder pads address lines here

also you really should have sent the progskeet back for bellow standard component layout
they should be fitted better than what you have recived
the company that sent you it should have checked them and sent them back not sent them out.

under distant selling regs you have 7 days to return for full refund no questions

also as it was a shop then under the distant selling regs they must pay for return postage for returning products (auctions are not obliged to do this)

i think there should be a recall of this product and the production of them checked at factory to insure the components are set square not off set.

i can see alot of problems and possible mass bricks due to the faulty boards

[d0nc0l0]

Originally Posted by baileyscream i know we went through this in p/m but for anyone else reading this. the progskeet user guide has the solder pads on the progskeet 1.2 mapped out except for the address lines so it is still usless to use without these this is for nor btw if progskeet get back to you please post the solder pads address lines here also you really should have sent the progskeet back for bellow standard component layout they should be fitted better than what you have recived the company that sent you it should have checked them and sent them back not sent them out. under distant selling regs you have 7 days to return for full refund no questions also as it was a shop then under the distant selling regs they must pay for return postage for returning products (auctions are not obliged to do this) i think there should be a recall of this product and the production of them checked at factory to insure the components are set square not off set. i can see alot of problems and possible mass bricks due to the faulty boards

I'm planing to buy one.. you think you can post a small tutorial how you got it working please.. thx

[baileyscream]

Originally Posted by d0nc0l0 I'm planing to buy one.. you think you can post a small tutorial how you got it working please.. thx

the injectus needed programing first (that was the problem here)

then the progskeet needs the bitstreem(for NOR or NAND as it doesnt come with any bitstreem on it) putting on via the injectus

this is where we are at atm

the guide from progskeet (see my guide i have linked it) has the NAND solder pins mapped but for NOR the address lines are missing

[d0nc0l0]

Originally Posted by baileyscream the injectus needed programing first (that was the problem here) then the progskeet needs the bitstreem(for NOR or NAND as it doesnt come with any bitstreem on it) putting on via the injectus this is where we are at atm the guide from progskeet (see my guide i have linked it) has the NAND solder pins mapped but for NOR the address lines are missing

The one i'm buiying it comes with
- Main board PROGSKEET 1.2
- Slave board PROGSKEET 1.2
- Adaptor PCB

do I need more than that?? thx
Because i see in the manual that they have one that is a full kit..

[baileyscream]

Originally Posted by d0nc0l0 The one i'm buiying it comes with - Main board PROGSKEET 1.2 - Slave board PROGSKEET 1.2 - Adaptor PCB do I need more than that?? thx Because i see in the manual that they have one that is a full kit..

if you dont have injectus allready then you need the full kit (injectus can be ordered from the same sites so if you have ordered the basic progskeet then just find the injectus and order that also (they are cheep)

[Kazrael21]

Originally Posted by xerxesrex Kazrael, mind to share where u get the skeet 1.2? thanks

http://www.vgcrepairs.biz/progskeet-...progskeet-v1.2

Use this coupon code to save some money too :WeBrewWii -I got it cheaper than advertised haha.
************* [ - Post Merged - ] *************

Originally Posted by baileyscream the guide from progskeet (see my guide i have linked it) has the NAND solder pins mapped but for NOR the address lines are missing

So I have 3 NAND models I am trying to recover from bad flashes, so i guess I dont need the address lines...Ill still be e-mailing progskeet to get those and I will post whatever replies I get here.
so I guess its because I am still very new at this but this is whats confusing me when I try to connect my chip:
NAND1 Connection:
Data signals
P41 = IO7 / DQ7
P40 = IO6 / DQ6
P39 = IO5 / DQ5
P38 = IO4 / DQ4
P37 = IO3 / DQ3
P36 = IO2 / DQ2
P35 = IO1 / DQ1
P34 = IO0 / DQ0
Control signals
P09 = CLE
P08 = ALE
P07 = WE
P06 = RE
P05 = CE_A
P04 = WP
P03 = CE_B
P02 = R/B#
NAND2 Connection:
Data signals
P49 = IO15 / DQ15
P48 = IO14 / DQ14
P47 = IO13 / DQ13
P46 = IO12 / DQ12
P45 = IO11 / DQ11
P44 = IO10 / DQ10
P43 = IO9 / DQ9
P42 = IO8 / DQ8
Control signals
P33 = CLE
P32 = ALE
P31 = WE
P30 = RE
P29 = CE_A
P28 = WP
P27 = CE_B
P26 = R/B#


**** I dont know what Im looking at .. A picture tutorial would be Ideal or if someone could explain what Im looking at.
************* [ - Post Merged - ] *************
@baileyscream what else do I need? this is everything I have.

[baileyscream]

Originally Posted by Kazrael21 snip @baileyscream what else do I need? this is everything I have.

right i see now
you just need 1 of the "y" adaptors (you have 2 in the pic)
and 1 "y" to clip cable (you have 4 in the pic)
your just missing a NAND clip

as far as i know the progskeet 1.2 still wont read from 2 nands at the same time yet.
but will soon

[Kazrael21]

Originally Posted by baileyscream right i see now you just need 1 of the "y" adaptors (you have 2 in the pic) and 1 "y" to clip cable (you have 4 in the pic) your just missing a NAND clip as far as i know the progskeet 1.2 still wont read from 2 nands at the same time yet. but will soon

Im looking at all the NAND clips and I dont know which one to get..I emailed them and asked for one thatll work best with progskeet v1.2 but they take forever to reply..--these are the clips IM looking at--http://www.vgcrepairs.biz/search-results?main_page=advanced_search_result&search_in_description=1&keyword=NAND+PCB&x=0&y=0

[baileyscream]

Originally Posted by Kazrael21 Im looking at all the NAND clips and I dont know which one to get..I emailed them and asked for one thatll work best with progskeet v1.2 but they take forever to reply..--these are the clips IM looking at--http://www.vgcrepairs.biz/search-results?main_page=advanced_search_result&search_in_description=1&keyword=NAND+PCB&x=0&y=0

NAND SOCKET "360-CLIP.COM"

thats the name of the one you want also you can see the pin header board (red)

[Kazrael21]

Originally Posted by baileyscream NAND SOCKET "360-CLIP.COM" thats the name of the one you want also you can see the pin header board (red)

This sucks I have spent almost an hour searching online for a distributer that ships to the United States with the NAND SOCKET 360-clip in stock.
Does anybody know of a distributer in stock that can ship to U.S?