[Kazrael21]

Originally Posted by d0nc0l0 do i need the 360 clips for a slim??

Im not sure, i have never worked with slims, but direct your question to
@baileyscream as I'm sure he may be of much more help.

[d0nc0l0]

Originally Posted by Kazrael21 Im not sure, i have never worked with slims, but direct your question to @baileyscream as I'm sure he may be of much more help.

thx... i got my v1.2 but i guess i have to wait for someone tutorial on how to do it the soldering part..

[Kazrael21]

Originally Posted by d0nc0l0 thx... i got my v1.2 but i guess i have to wait for someone tutorial on how to do it the soldering part..

Yup I hope some come out soon, once I get my 360 clips I will expieriment around a bit
************* [ - Post Merged - ] *************
@Jotown did you ever get your comp to recognize your progskeet?
************* [ - Post Merged - ] *************
well just checked the mailbox and guess what I found in there..MY 360 CLIP!! ill start expierimenting tomorrow. :D i hope everything goes well..

[Psymon]

Hey guys,

i'm also trying to dump my NAND with the Progskeet 1.2 and the NAND clip. My Problem is that winskeet doesn't recognize the correct NAND when i click the AUTO Button. It says 0C01010000 UNKNOWN. Hope we find a way. BTW I made a connection from Progskeets 3.3V to Ys 3.3V and Progskeets GND to Ys GND.

[Tommy1603]

Originally Posted by Psymon Hey guys, i'm also trying to dump my NAND with the Progskeet 1.2 and the NAND clip. My Problem is that winskeet doesn't recognize the correct NAND when i click the AUTO Button. It says 0C01010000 UNKNOWN. Hope we find a way. BTW I made a connection from Progskeets 3.3V to Ys 3.3V and Progskeets GND to Ys GND.

I had the same problem last night, it's just a bad connection, make sure the clip fits nicely on the nand chip, sometimes there's a fuse next to the nand chip which will stops you from putting the clip on. Als make sure all the connections from the clipboard to progskeet to slaveboard are good. I just reconnected everything and it worked.

[Psymon]

Originally Posted by Tommy1603 I had the same problem last night, it's just a bad connection, make sure the clip fits nicely on the nand chip, sometimes there's a fuse next to the nand chip which will stops you from putting the clip on. Als make sure all the connections from the clipboard to progskeet to slaveboard are good. I just reconnected everything and it worked.

Did you also connect 3.3V and GND or only the 3.3V?? Did you do anything else on your Progskeet 1.2??
Thanks

Edit: I just soldered everthing again, but same problem. It seems as if on small contact of the NAND clip is a lot shorter than the others. Maybe it isnt connected... I will buy a new Clip and try again.

[Tommy1603]

Originally Posted by Psymon Did you also connect 3.3V and GND or only the 3.3V?? Did you do anything else on your Progskeet 1.2?? Thanks Edit: I just soldered everthing again, but same problem. It seems as if on small contact of the NAND clip is a lot shorter than the others. Maybe it isnt connected... I will buy a new Clip and try again.

I only soldered the 3.3v, not the GND.
Maybe a very obvious question but did you update the bitstream of the Progskeet?

[Jotown]

Ok, I get my problem.

I changed nothing on the board. (see the picture)

1. Install the Infectus driver for Injectus --> connect only the Injectus via usb to PC
2. Disconnect the Injectus and connet it via 15 pin cable to the Progskeet 1.2, then connect it to the PC.
Load the Bitstream (http://www.progskeet.com/forum/viewtopic.php?f=9&t=4064) with the Infectus Programmer.
3. When it´s done disconnect it from the PC and connect the Slaveboard instead the Injectus. Then connect it to the PC
Install the driver manually.

When I run the shortcut analysis I get the same message (see the attechment)

Thank you.

[Kazrael21]

Originally Posted by Jotown Ok, I get my problem. I changed nothing on the board. (see the picture) 1. Install the Infectus driver for Injectus --> connect only the Injectus via usb to PC 2. Disconnect the Injectus and connet it via 15 pin cable to the Progskeet 1.2, then connect it to the PC. Load the Bitstream (http://www.progskeet.com/forum/viewtopic.php?f=9&t=4064) with the Infectus Programmer. 3. When it´s done disconnect it from the PC and connect the Slaveboard instead the Injectus. Then connect it to the PC Install the driver manually. When I run the shortcut analysis I get the same message (see the attechment) Thank you.

OKAY, soo today uf6667 made it very clear "DO NOT TEST FOR SHORTS ON VERSION 1.2 OR ELSE I WILL GUT YOU MOTHERFU(KERS!" he has not yet said why we cannot test on the new version but ill go ahead and say to ANYONE USING THE NEW PROGSKEET V1.2 DO NOT TEST FOR SHORTS!..**for those who have tested for shorts do not worry your board is not ruined, uf6667just doesnt want to here about all the shorts reported since theyre not a problem**

as of today november 1st a new bitstream for progskeet v1.2 has been released to fix the problem with NAND where it would only recognize secondary nand (on both A and B)
- switchis now inverted you can find the download here http://www.progskeet.com/forum/viewtopic.php?f=9&t=4138

[Decoy]

so @uf6667 replied to me (Haidarooz) and posted the progskeet 1.2 pinout
here it is: http://t.co/Y34YVHPQ