[lilkuz2005]

i have 4 ps3's that i want to downgrade back to 3.55, 3 of them are the phat models 1 is a 60gb, 1 is a BC 80gb, and 1 is a 40gb model, then i have a slim that i want to downgrade as well, im looking at buying the progskeet v1.2 but im not sure what all i should order as i have a few NOR consoles and a few nand consoles. can anyone tell me what i should buy ?

[Decoy]

You need :

Progskeet 1.2 + injectus programmer
NAND pcb board
360-clip NAND(for the NAND ps3 only)
And a dev board (e3 card reader , eclips3 , any other dongle that allows fsm...)

As for the fat ps3s it's better to solder ..
But for the nor you will use the almost solderless solution(clips)

[p2user]

Is it better to try and buy a progskeet v1.1 instead of v1.2 ? I'm trying to recover my Fat 40gig PS3 with NAND and completely new to this.

Also which sites have people been using to order their kits? Are there any in UK?

[d0nc0l0]

Originally Posted by Decoy You need : Progskeet 1.2 + injectus programmer NAND pcb board 360-clip NAND(for the NAND ps3 only) And a dev board (e3 card reader , eclips3 , any other dongle that allows fsm...) As for the fat ps3s it's better to solder .. But for the nor you will use the almost solderless solution(clips)

can you tell me is ps break dongle can be use for fsm?? i already have the v.1.2 and i'm ready to do it but i'm still have some questions... u know a tutorial using the v.1.2 ?? do you have a like a pic of the motherboard where the pins go?? with labels?

[d0nc0l0]

Originally Posted by baileyscream the injectus needed programing first (that was the problem here) then the progskeet needs the bitstreem(for NOR or NAND as it doesnt come with any bitstreem on it) putting on via the injectus this is where we are at atm the guide from progskeet (see my guide i have linked it) has the NAND solder pins mapped but for NOR the address lines are missing

for some reason i can't get the drivers install to test the pins.. i'm using windows 7 .. 64 do u know why? i already did the infectus and bitstream.. thx for all your help

[Kazrael21]

every time i try to dump my nands it says NAND0 32 bad blocks and NAND1 32 bad blocks. ive filed the NAND clip so i dont think it can sit any flatter on the board, could the wire im using make a difference?

[Stolas]

I'm currently stuck trying to dump the nand.

So I have the Progskeet 1.2, and I've used injectus to update it to the latest bitstream. Now I've replaced the injectus with the progskeet slave one, and I have attached the nand clip to my fat ps3 60gb CECH. When I launch winskeet and press the auto button for nand 1, I get unknown and seemingly randomly changing numbers. I've tried repositioning the clip over and over, but I never get samsung to appear.

So what am I missing? I heard someone say something about v3.3, but that apparently require soldering, which I wanted to avoid by buying the clips :/.

[Kazrael21]

Originally Posted by Stolas I'm currently stuck trying to dump the nand. So I have the Progskeet 1.2, and I've used injectus to update it to the latest bitstream. Now I've replaced the injectus with the progskeet slave one, and I have attached the nand clip to my fat ps3 60gb CECH. When I launch winskeet and press the auto button for nand 1, I get unknown and seemingly randomly changing numbers. I've tried repositioning the clip over and over, but I never get samsung to appear. So what am I missing? I heard someone say something about v3.3, but that apparently require soldering, which I wanted to avoid by buying the clips :/.

you still have to solder the 3.3v to the 3.3v on the "Y" clip, but im in the same spot as you

************* [ - Post Merged - ] *************
i have used alcohol and a brush to clean the NAND pins on the chip and clip and ive cut and filed the clip so it sits flat against the board but still cant get a decent dump

[Inali]

I can't get my Progskeet 1.2 working on PC :/ Well, half working.

This is what I did so far:

1. Install the Infectus driver for Injectus --> connected Injectus via usb to PC WITH PROGSKEET ATTACHED (didn't know I needed it not attached...)
3.Load the Bitstream with the Infectus Programmer.
3. When it´s done disconnect it from the PC and connect the Slaveboard instead the Injectus. Then connect it to the PC

Aaaand, nothing happens. PC doesnt detect new hardware. At all. On any usb port. I think my slave board is busted? It looks okay. I tried connecting only INJECTUS to pc, and it works, and the progskeet main board must work, as I already programmed the newest bitstream to it...

Help please!! I can take pics if needed. Running Windows 8 Pro x64

[d0nc0l0]

Originally Posted by Kazrael21 you still have to solder the 3.3v to the 3.3v on the "Y" clip, but im in the same spot as you ************* [ - Post Merged - ] ************* i have used alcohol and a brush to clean the NAND pins on the chip and clip and ive cut and filed the clip so it sits flat against the board but still cant get a decent dump

How you able to get your pc to recognize the progskeet? I'm having the same issue the guy that comment on top of my post is having... Yhx for your help