[baileyscream]

Originally Posted by ellada (min version checker can be downloaded from here: http://www.mediafire.com/?0mlju38vbqlizod ) can some one re-upload pls ? Thanks

LINK UPDATED

[Sarah1331]

Come please help I purchased a y adaptor and injectus to account for my soldering

All dumps same as my previous ones
NAND 0 1bad block
NAND 1 7bad blocks can anyone remap these for me please
I have tried irc but nobody helped me out

My dumps are at

https://hotfile.com/dl/178226120/4f3c942/nand.rar.html

[ellada]

Originally Posted by MJ999 http://www.crocko.com/A214EA620D0246...inVerCheck.rar DOWNLOAD LINK

thanks a lot have a nice day

[Sarah1331]

Please people I have patched the dumps I have and flashed them and it has bricked the console

Flashed the orig dumps back and it works

[baileyscream]

Originally Posted by Sarah1331 Please people I have patched the dumps I have and flashed them and it has bricked the console Flashed the orig dumps back and it works

geeze your lucky

1st. put the ps3 back together and re-install what ever firmware is on it.
this will hopefully insure any bad areas you may have flashed back are restored.
(although there are areas that the firmware simply does not touch)

2nd i suspect not all the pins in the clip are touching the legs of the nands propperly.

3rd clean the clip and legs with alcohol wipes then try again.

4th use good quick clamps to hold the clip in place and check the clip is sat flush

5th check the flat cable is sat square in the ffc clip's

6th NEVER FLASH BACK A DUMP THAT IS NOT 100% VERIFIED

--------------------------------------------------------------
i'm away now for the weekend.
but take your time and it will suddenly start working if you keep repeating the above steps

[Sarah1331]

I have lifted the tsop and it's got 100% connection I have soldered to each leg and got the same no errors in win skeet ect

I have reinstalled ofw that is on

I have reseated the clip loads of times

Is this a good enough clamp this is what I have used

I haven't dumped the nands just 5 or 10 times I have dumped 100's of times

I would never advise anyone to do this but I do have extensive knowledge of nands and how bad blocks work

They go the the end in reverse order I just need to know how to find the bad block locations to remap them

[Sarah1331]

Can someone upload a good dual NAND dump I can work from please

@baileyscream
You are a good person thank you for all your help I truly mean it but some
people just won't help others I went on irc and ended up helping 2-3 people and on tx I send people parts for free and help as much as poss but I am starting to realise good help is hard to find I feel like nobody helps me back

[fudd69]

hi. I have a bricked ps3 and i have e3 flasher. In order to unbrick it I have to solder a wire from tristate to SBE or to a GND point but the tristate point doesn' t exist any more because the soldering made it come off. i have soldered another point to GND just to try it and the PS3 halts on boot up as it should do if the point soldere were Tristate. Now when I install the e3 flasher I can backup the NOR but i cannot write it . someone could tell me why? thanks

[Morto_]

Hey Guys,

I have ordered a Progskeet 1.2.
But i cant find the right diagram for my COK-002 mainbord can someone help me.

[meetdeath]

i have the Minimus 32 AVR USB
device name AT90USB162

think what iam asking is if i follow the tutorial is it ok for me to use this device or is the a diffrent fsm for each device.
if the device is working and and i follow the gide will i be OK ?
prity sure this is gona be the hardest thing i've done
i am thinking solderless and just give it a go been reading all week and will be reading till i fix the problem i made
tryed to downgrade but left disk in (my folt)
so if any one wont to help out a silly man ur wellcome to pm me

if any one had a 3.55 and mucked up,i die a little bit each day.