[handys]

Good day!
Thanks in advance for your attention.
I have a problem with the console firmware update 3.55 with Roger, Roger on firmware 3.7 was brick. When the console is working for 4-5 seconds and then turns off. There is a dump, but I do not know from what firmware. Loaded dump, with a difference of firmware versions, of the effects were not, the console shuts off after 4-5 seconds. The console has undergone a decrease in the firmware (downgrade)

[DEFAULTDNB]

Originally Posted by handys The console has undergone a decrease in the firmware (downgrade)

Sounds like hash panic, guessing your didnt dehash?

Do you have a flasher, and a dump?

[handys]

Yes i have a flasher, and a dump, the dump worker, he changed programs you PS3 Nor patcher to downgrade. Dump is http://rghost.ru/41424498

[DEFAULTDNB]

@baileyscream knows absolutely best in this situation, so I have found a similar thread with a lot of his wisdom (in red is his answer to the problem):

heres the story: i got a used slim with 3.55cfw but i wasnt sure which cfw. it just had a PsHAX coldboot. I was told that it was downgraded before and cant install any other cfw. Ive heard that it IS in fact possible but you have to dehash you system first with rebugs toggle qa, so i tried it and followed the directions and proceeded to install kmeaw afterwards. for anyone else at this point first try the key combo to see if QA flag has actually been installed (if it has then putting it on is actually turning it off) if the key combo doesnt do anything then install QA flag and check its active by doing the key combo (if still nothing happens this is the point to ask for help) the install went to about 35% then bricked. now the system wont boot.....and i dont mean the green light no audio/video/recovery brick. mine doesnt even stay on for more than 5 seconds. it goes from the red standby light to green (with no activity) and then shuts off after 5 seconds and all the lights go off. no red standby or anything.if i hit the power button again, the red light turns back on and im back in standby mode. and the cycle just repeats. this is called a De-hash fail the downgrade hashes are still in the system and it is now in a panic (i suspect like you are ) i used memdump to make a backup or my nor before just in case, and i also have an E3 flasher. ive only used the E3 once and that was to downgrade my friends system a long time ago. i didnt know that E3 could only be used on 1 console. E3 made that samsung fix, but im guessing that i have to update it with the first system (which is impossible because my friend sold it). no your safe you can update to the multi console update when your E3 is in your ps3 (i suspect your panic is now fading ) on top of that, the e3 dump checker says i have a bad dump or wrong format (can i convert it?). ok right now delete that bloody usless E3 dump checker its more harm than good. it doesnt check everything that needs checking and you have a 85% chance of bricking if you trust it so BIN IT i keep reading about soldering the tristate to the sbe to prevent the system from turning off, but i think thats only for when the system shuts down while dumping the nor. nope its for dual booting and this situation so you need to solder it so basically this is what i understand so far: i need to solder and use the e3 to prevent the ps3 from shutting down, but since the e3 was already used on another system, i need to apply the e3 samsung fix so i can use it on multiple systems, but that has to be done from a system that actually STAYS ON for longer than 5 secs (if not the actual system it was originally used on). once the tristate is soldered to sbe it will halt the system (it wont boot any further or shut down) nb if it does shut down then just solder tristate to a gnd point is this all accurate? someone please tell me im wrong and theres a way around it. Rogero, if youre reading this, I REALLY NEED YOUR HELP. i did all this cuz i wanted the install the new 4.30cfw. please, anyone out there, im clueless and any help is appreciated. thanks to all in advance.

after the above in red and your system has halted. update the E3 with the muli console update and do a dump of your nor then verify it and then patch it (your treating it as though your downgrading) then put the ps3 into fsm and downgrade to 3.55 rogero then QA flag then de-hash with 3.55 genuine (NOT CFW) firmware now you should have 3.55 boot as normal. go relax. have a drink. follow my guide for the downgrade:- http://www.ps3hax.net/showthread.php?t=39766

I hope you can relate to this and you can figure it out. I have very little knowledge of flashers.

[haz367]

FYI...the extracted valid dump, it shows ur coming from a 3.56 downgrade - ros0 = 3.56 firmware..maybe some to do with this?! goodluck on fix

[handys]

Thank you for your attention, but I do not understand, and I can not find the right answers, I would be a lot easier if I had written by experts specifically what I need to do for repairing my console.

[baileyscream]

Originally Posted by handys Good day! Thanks in advance for your attention. I have a problem with the console firmware update 3.55 with Roger, Roger on firmware 3.7 was brick. When the console is working for 4-5 seconds and then turns off. There is a dump, but I do not know from what firmware. Loaded dump, with a difference of firmware versions, of the effects were not, the console shuts off after 4-5 seconds. The console has undergone a decrease in the firmware (downgrade)

all rogero3.55 firmware have been patched for downgrading
so if you stick with rogero then all his 3.55 firmware's will install even if you havent de-hashed.

my concern is that you have flashed an unknown backup to your ps3.
are you 100% sure this backup from your ps3?
if not then you have a perma-brick NO RECOVERY

how long has the rogero 3.55 v3.7 been installed on your system before the problem started?

if its been on a while then its more likely your ps3 is getting hot instantly and sutting down. look into a re-ball of the cpu /gpu

if it happened as soon as you installed the firmware then what did you have installed before you updated and what is the hash check of the rogero 3.55 v3.7 that you have (it may be corrupted)

as there are somany possibile reasons to why this has happened you need to give as much info as you can no matter how small / poinless that info may seem

ie (i was holding my controller when i started the up date then i put it down oh it banged the table) << sounds pointless to tell us but even that could help us

[handys]

how long has the rogero 3.55 v3.7 been installed on your system before the problem started?

On my system was installed Rogero v.3.1 and then I was decided update to Rogero v. 3.7 (from recovery). But on 49% of update PS3 turn off and after this don't want to turn on.

are you 100% sure this backup from your ps3?

Yes it is backup of this PS3 but i don't remember of which firmware it was dumped.

I find in PS3 devwiki such info about De-Brick procedure:
Last point of procedure:
Power off the console from behind (using E3's switch) and put all switches on the E3 down. Remove/disconnect the Tristate cable.

Remove/disconnect the Tristate cable. - This point of procedure i don't try, maybe it is a problem why PS3 don't turn on normally after De-Brick procedure???

[baileyscream]

Originally Posted by handys On my system was installed Rogero v.3.1 and then I was decided update to Rogero v. 3.7 (from recovery). But on 49% of update PS3 turn off and after this don't want to turn on. Yes it is backup of this PS3 but i don't remember of which firmware it was dumped. I find in PS3 devwiki such info about De-Brick procedure: Last point of procedure: Power off the console from behind (using E3's switch) and put all switches on the E3 down. Remove/disconnect the Tristate cable. Remove/disconnect the Tristate cable. - This point of procedure i don't try, maybe it is a problem why PS3 don't turn on normally after De-Brick procedure???

the part where i said to give as much info as possible. this would be that time.

you have an E3 connected to your ps3?
and you have the tristate wire soldered?

if the tristate is soldered then your ps3 will halt during boot up. it will also prevent it from shutting down if its the firmware on the nor that is at fault.

if the tristate is wired and the ps3 is shutting down then you need to put the first switch up (flash fun) and the rest down. then plug in the mains lead then power on the ps3.
it should now halt and not shut off.

if it shuts off then its hardware getting hot

i have just had the same prob with a phat nor ps3 with DIA-001 board where the heat transfer pad fron the chip next to the nor was missing. when i replaced it the ps3 now halts

so check all your heat pads are in the correct places on the board and not missing then try again.

if it still wont boot then check the fan is attached and the heat sink & fan is attached propperly.

if it still wont halt then attach the tristate point on the ps3 to a vcc (also known as earth) on the ps3. and it should halt

if it still does not halt then you may need to have the ps3's cpu / gpu re-balled

[handys]

Thanks for your advice, this evening I will try again, and write what will be the result.