[Okilim]

Hi,

Thanks for reading, The story goes like this.

First i dump both nand with solderless Clip on a COK-002 and validate it via Ps3devwiki, also post @ http://www.ps3hax.net/showthread.php?t=46100&page=19 for validate.

"
Originally Posted by Okilim
Here's the mediafire Link
http://www.mediafire.com/?k5p4d6so3janeas
PS3 Model: CECHExx
Mobo: COK-002

NOTE:
- The IDPS is 3 and Not 4 as in the WikiDev
- The FFs are 24.76% > 24.54% as in the WikiDev

At Address : 00091800 (trvk_prg) it is not as in the guide but in DevWiki:
it can be that way:
Link: http://www.ps3devwiki.com/wiki/Flash...ogram#trvk_prg

At Address : 00093800 (trvk_prg) it is not as in the guide and WikiDev
but the size is correct.

It Could be valid, but if i were you i double check again and dump. "

So i change bitstream and dump it with wiring and compare with my solderless dump they are identical. With no doubt, i patch it, Split it and write it on my PS3, boom.. PS3 on then off after 8 sec.

But after writing back my original dump, the PS3 boot normally again.
I also follow Barleyscream guide to confirm the patching and spliting but the result is same.
try remove all wire and write it with solderless clip again but result is same.
Now i dont know what else i can try.
Any suggestion?

Best regards,
Oki

[3absiso]

Originally Posted by Okilim Hi, Thanks for reading, The story goes like this. First i dump both nand with solderless Clip on a COK-002 and validate it via Ps3devwiki, also post @ http://www.ps3hax.net/showthread.php?t=46100&page=19 for validate. " Originally Posted by Okilim Here's the mediafire Link http://www.mediafire.com/?k5p4d6so3janeas PS3 Model: CECHExx Mobo: COK-002 NOTE: - The IDPS is 3 and Not 4 as in the WikiDev - The FFs are 24.76% > 24.54% as in the WikiDev At Address : 00091800 (trvk_prg) it is not as in the guide but in DevWiki: it can be that way: Link: http://www.ps3devwiki.com/wiki/Flash...ogram#trvk_prg At Address : 00093800 (trvk_prg) it is not as in the guide and WikiDev but the size is correct. It Could be valid, but if i were you i double check again and dump. " So i change bitstream and dump it with wiring and compare with my solderless dump they are identical. With no doubt, i patch it, Split it and write it on my PS3, boom.. PS3 on then off after 8 sec. But after writing back my original dump, the PS3 boot normally again. I also follow Barleyscream guide to confirm the patching and spliting but the result is same. try remove all wire and write it with solderless clip again but result is same. Now i dont know what else i can try. Any suggestion? Best regards, Oki

Ummm;
good that it is working back using the original dump;
my experiance ir more in the Nors, but i suggest you go to wikidev IRC and put your dump and explain what happened, you may find someone help you, say that you followed Wikidev validation but i found these issues to my dump. i hope someone will help.
Reagrds

[davey6693]

Originally Posted by Okilim Hi, So i change bitstream and dump it with wiring and compare with my solderless dump they are identical. With no doubt, i patch it, Split it and write it on my PS3, boom.. PS3 on then off after 8 sec. But after writing back my original dump, the PS3 boot normally again. I also follow Barleyscream guide to confirm the patching and spliting but the result is same. try remove all wire and write it with solderless clip again but result is same. Now i dont know what else i can try. Any suggestion? Best regards, Oki

Possibly extremely dumb of me here Oki, but since I just downgraded successfully and was following your story, my system also turns off after 8 seconds after successful NAND flash. At that point I put in my dev board (E3 card reader) and hit power and quickly eject, to trigger service mode, and then after that was able to flash using a modified cfw. Are you not getting to that stage with your dev board inserted?

[Okilim]

Since flashing back original back and it boot, i chicken out and give back the PS3 to its owner. I will ask my friend to bring over again and try.
^^

[Sarah1331]

Flash your patch
And continue with fsm and update using fsm
this is normal for NAND consoles

You have a good dump you will always be good