[CopyLifted]

Originally Posted by monu1232009 i found a problem in linker's wire between d11 and d12 i corrected it, then i took a backup and patched then flash is to my console {100000} then i remove linker and also flasher from hdd slotthen put my hdd in and my psp at right most port then put power cable board . then i pressed power plus eject. my ps3 turned on for 3 or 4 sec and turned off itself without stand by light. i thought i should stop at this stage and asked at this thread is it bad thing or good . also thank you all senior member to give me direction for checking again linker wires. thank you

You say with out stand by light? As in there is no red light when it shut off?

It sounds like it has entered FSM, but I am confused as to what you mean by "without stand by light".

When it shuts off, is there no red light, solid red light, or blinking red light?

Also, what did your psp report on screen when this all happened?

[monu1232009]

Originally Posted by CopyLifted You say with out stand by light? As in there is no red light when it shut off? It sounds like it has entered FSM, but I am confused as to what you mean by "without stand by light". When it shuts off, is there no red light, solid red light, or blinking red light? Also, what did your psp report on screen when this all happened?

with out stand by light {there is no red light}.
i think there was no additional message at psp when this all happened

[Mr.Dutch]

@monu1232009 , did you used the psp earlier to get into fsm?, because i thought the psp was not that reliable as a fsm dongle.

[monu1232009]

no it is my first time

[Mr.Dutch]

Originally Posted by monu1232009 no it is my first time

i never had to use a psp since i don't do downgrades or stuff like that, but i did read people had problems using a psp.

also, when the red light turns off, did you still had the 5V from the psu on the mainboard? (to rule out psu issues)

[monu1232009]

yes psu is giving 5v to mobo. when i power my ps3 from main there is a red light of stand by as normal then i turn on psp there is a freen light for 3 or 4 sec and then there is no light.{no red light also}

[baileyscream]

Originally Posted by monu1232009 yes psu is giving 5v to mobo. when i power my ps3 from main there is a red light of stand by as normal then i turn on psp there is a freen light for 3 or 4 sec and then there is no light.{no red light also}

i have had the no light fault with e3 when trying to dual boot.
i just re-flashed and it solved it.
but your trying to patch a few dumps together to get 1 good dump.

you could try removing the clip from e3 (this way if the clip is on the nor good your not disturbing that point) and see if the ps3 will now enter fsm.

if its still the same do a dump and check it. if its good try flashing your patch again.

if its bad try flashing your "built from many dumps" dump again. but i fear we may now be at a loss
i really want all your dumps. every one you can find putting in a rar and uploading.
also send a dump of how it is now.

i am really stuck untill i get that first dump though.
the one you say mj999 checked as ok that you sent me was allready byte reversed i want it before you byte reversed it.
flow rebuilder can reverse sometimes with out giving an error so i need it before this stage.
so send me every single dump you have. its my best shot at finding a good dump.

[monu1232009]

ok please give me an hour
************* [ - Post Merged - ] *************
i am uploading again now may be it takes 30 min . .rar contains all four untouched dump of my ps3 the dump named bkpps30.bin is the one which was checked by mj999 .please help me one more time
************* [ - Post Merged - ] *************
http://www.mediafire.com/?e4j98vdzhh486tw
************* [ - Post Merged - ] *************
here is my back up http://www.mediafire.com/?e4j98vdzhh486tw
************* [ - Post Merged - ] *************

Originally Posted by baileyscream i have had the no light fault with e3 when trying to dual boot. i just re-flashed and it solved it. but your trying to patch a few dumps together to get 1 good dump. you could try removing the clip from e3 (this way if the clip is on the nor good your not disturbing that point) and see if the ps3 will now enter fsm. if its still the same do a dump and check it. if its good try flashing your patch again. if its bad try flashing your "built from many dumps" dump again. but i fear we may now be at a loss i really want all your dumps. every one you can find putting in a rar and uploading. also send a dump of how it is now. i am really stuck untill i get that first dump though. the one you say mj999 checked as ok that you sent me was allready byte reversed i want it before you byte reversed it. flow rebuilder can reverse sometimes with out giving an error so i need it before this stage. so send me every single dump you have. its my best shot at finding a good dump.

did you recieve?

[baileyscream]

Originally Posted by monu1232009 ok please give me an hour ************* [ - Post Merged - ] ************* i am uploading again now may be it takes 30 min . .rar contains all four untouched dump of my ps3 the dump named bkpps30.bin is the one which was checked by mj999 .please help me one more time ************* [ - Post Merged - ] ************* http://www.mediafire.com/?e4j98vdzhh486tw ************* [ - Post Merged - ] ************* here is my back up http://www.mediafire.com/?e4j98vdzhh486tw ************* [ - Post Merged - ] ************* did you recieve?

downloading now
will let you know what i find. i wont be quick as i will be looking deep into them

[monu1232009]

ok sir bailey