[M8nTrap]

nothing new!

yesterday on IRC, domelec do many pg1.2 test dump's!
to be sure about bitstream errors.

and the progskeet1.2 status is always the same:

only dump's ps3 NAND'S (read/write)...
tested in this way:
.solderless (clip)
.external powering
.latest winskeet

ps3 NOR are only readable via :
.WinSkeet40000_111004
.Zadig (driver change)
.libusb0 driver

et voila! that's all, no date!

[Sarah1331]

Just like the dual NAND for progskeet 1.1 adaptor board it will never come there's an inherent flaw

The people that released it

Just wait on a addon PCB coming for the skeet 1.2 it will be announced here first


Sent from my iPhone 5 using Tapatalk

[underwurlde]

@Sarah1331 , as promised:

How to turn a ProgSkeet v1.2 into a v1.1 such that it works thread here: http://www.ps3hax.net/showthread.php?t=48799

Tested the dumping and programming of a single NAND: Worked.

TBD
1) Testing dumping and programming of a NOR.
2) To downgrade my NAND based PS3.

Notes
Yes, not a simple exercise to convert the v1.2 to a v1.1... some tricky wiring and the need for a USB driver IC. BUT if everyone happy to solder fine wires from their 'Skeets to 0.5mm pitch flash IC's, then this conversion should be well within your capabilities.

Andy

[domelec]

Originally Posted by M8nTrap nothing new! yesterday on IRC, domelec do many pg1.2 test dump's! to be sure about bitstream errors. and the progskeet1.2 status is always the same: only dump's ps3 NAND'S (read/write)... tested in this way: .solderless (clip) .external powering .latest winskeet ps3 NOR are only readable via : .WinSkeet40000_111004 .Zadig (driver change) .libusb0 driver et voila! that's all, no date!

actually i used latest winskeet
lastest 1.2 bitstream 2121
nand clip
and power from skeet to adapter board
and used winusb driver
dumped both nands on a sem-001 and a cok-002
also flashed both nands back with patched nands
worked ok
now working on testing the nor consoles

[underwurlde]

Ah! So you used SOLDERLESS NAND BitStream?!?

I wonder if this is the difference that ensures that my in-circuit NAND BitStream DOES NOT WORK. Hmmmmmmmmmmmmmmmmmmmmm.

Andy

[domelec]

Originally Posted by underwurlde Ah! So you used SOLDERLESS NAND BitStream?!? I wonder if this is the difference that ensures that my in-circuit NAND BitStream DOES NOT WORK. Hmmmmmmmmmmmmmmmmmmmmm. Andy

i used the latest bitstream for v1.2

ProgSkeet_12_121106_2121

[underwurlde]

Yarp! 'tis what I used.



Didn't work.



Andy not happy. Andy Sad. Andy FIX

[domelec]

Originally Posted by underwurlde Yarp! 'tis what I used. Didn't work. Andy not happy. Andy Sad. Andy FIX

strange has i have now tried it a few times on a sem-001 board and a cok-002

and worked everytime
skeet v1.2
with last bitstream as above
360-nand clip and adapter pcb
3.3v wire from skeet to adapter
gnd from skeet to adapter
r7 closed
r8 open

Winskeet111205
winusb driver

[underwurlde]

Connected a NAND OK (Dual NAND, forget it), dumped it OK....

...But...

Poxy WinSkeet (including the version you refer to) just kept crashing every time I try to program. Tried it on Win XP and Win 7.

My v1.2, when set up as a v1.1 works fine though.

Go figure. You are lucky dude, for what ever reason!

Andy

[domelec]

very strange mate
i only read and write 1 nand at a time
as only nand 1 tab in winskeet works (nand 2 tab has never worked)

im using win xp sp3 32bit
and an old dell d505 laptop with intel chipset
which i have used since i got v1.1 2 years ago
and now the 1.2 i got just for testing
************* [ - Post Merged - ] *************
think i just missed u come on irc
was it u?