|
|
12-20-2012
|
#61 | |
|
Member
 Join Date: Aug 2011
Posts: 124
Likes: 8
Liked 1 Time in 1 Post
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
ITS STAYS ON YES!!! WHATS NEXT???
************* [ - Post Merged - ] *************
|
|
|
|
|
12-20-2012
|
#62 | |
|
Senior Member
 
Join Date: Feb 2011
Posts: 1,487
Likes: 531
Liked 1,010 Times in 506 Posts
Mentioned: 486 Post(s)
Tagged: 0 Thread(s)
|
|
|
|
|
|
|
12-20-2012
|
#63 |
|
Member
Join Date: Aug 2011
Posts: 124
Likes: 8
Liked 1 Time in 1 Post
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
oh wait i fu*** again, so first time e3 flasher was not connected to motherboard and i got hdd is not connected now i connected e3 flasher to motherboard again i got same problem it turns off after 5 sec. Can the problem be another flasher, i have 2 of them?
|
|
|
|
|
12-20-2012
|
#64 | |
|
Senior Member
Join Date: Feb 2011
Posts: 1,487
Likes: 531
Liked 1,010 Times in 506 Posts
Mentioned: 486 Post(s)
Tagged: 0 Thread(s)
|
ok i see you have the black screen i think your still in fsm download the files from the E3 guide then goto the "downgrade in fsm" step follow everything from that step. DO NOT MISS ANYTHING OUT & DO NOT CHANGE ANYTHING IN THE STEPS. @MJ999 the dump you checked was a good dump. i no longer need the file dooma sent you in p/m as he has comfirmed the file he sent me was the same one he sent you. @playerkp420 i still have no idea why the dump was different for you unless it was either corrupted during the transfer to / from the file share site or a different dump was uploaded & posted to the thread by mistake. i just dont get it 
|
|
|
|
|
|
Likes: (1) |
|
12-20-2012
|
#65 |
|
Member
Join Date: Aug 2011
Posts: 124
Likes: 8
Liked 1 Time in 1 Post
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
@baileyscream
thanks for helping i will repeat process tommorow, so again solder flash it and cut wire...
|
|
|
|
|
12-20-2012
|
#66 | ||
|
Senior Member
Join Date: Feb 2011
Posts: 1,487
Likes: 531
Liked 1,010 Times in 506 Posts
Mentioned: 486 Post(s)
Tagged: 0 Thread(s)
|
now what does it do? ps there is a chance the E3 clip is not connected propperly now that it has been removed / replaced lets just remove it and get you downgraded then we can start messing with the E3 ************* [ - Post Merged - ] *************
right now we know the nor has been flashed there is no need to carry on flashing it. just slow down and wait for me to reply before just doing something. Last edited by baileyscream; 12-20-2012 at 06:18 PM. |
||
|
|
|
|
12-20-2012
|
#67 |
|
Member
Join Date: Aug 2011
Posts: 124
Likes: 8
Liked 1 Time in 1 Post
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
YEEESSS!! IM ON 3.55 AND I HAVE INSTALL PACKAGE FILES AND EVERYTHING!!
i dont know how but im on 3.55 i think kmeaw. now i want to go to rogero 4.30 v2.03 i need to install lastest multiman on kmeaw and direct update to rogero 4.30? or Last edited by dooma; 12-20-2012 at 06:57 PM. |
|
|
|
|
12-20-2012
|
#68 | ||
|
Senior Member
Join Date: Feb 2011
Posts: 1,487
Likes: 531
Liked 1,010 Times in 506 Posts
Mentioned: 486 Post(s)
Tagged: 0 Thread(s)
|
you need to QA dehash do it now before you do anything else again its in my guide --------------------------------------------------------------------------------- next time give all info this is from p/m with my reply ---------------------------------------------------------------------------- READ THIS so i cut tristate and gnd wire, start ps3 and it stayed on  and then i got message HDD is not connected. Then i remember i forgot to connect e3 flasher to motherboard hdd slot and i did that with my other e3 flasher because he can fit perfectly and i turned on ps3 and got same problem ps3 turn off after 5 sec[/QUOTE]the e3 doesnt use the sata if you hold the E3 up to a strong light you will see the tracks connected to the hdd's sata connector on the E3 go to the esata port on the front of the E3 board. unplug the E3 from the hdd does the ps3 turn back on if no unplug the connector on the E3 board for the ribbon (going to nor clip) ps3 should now turn on ************* [ - Post Merged - ] *************
if you dont QA dehash first then i'm out of here!!! stop editing your post and read the thread !!!!
Last edited by baileyscream; 12-20-2012 at 06:34 PM. |
||
|
|
|
|
12-20-2012
|
#69 | |
|
Member
Join Date: Aug 2011
Posts: 124
Likes: 8
Liked 1 Time in 1 Post
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
if you hold the E3 up to a strong light you will see the tracks connected to the hdd's sata connector on the E3 go to the esata port on the front of the E3 board. unplug the E3 from the hdd does the ps3 turn back on if no unplug the connector on the E3 board for the ribbon (going to nor clip) ps3 should now turn on ************* [ - Post Merged - ] ************* ffs if you dont QA dehash first then i'm out of here!!! stop editing your post and read the thread !!!! [/QUOTE]sorry im too excited, i know how to qa dehash it's easy  Thank you for everything, I want to donate you some money, do you have paypal?
|
|
|
|
|
|
12-20-2012
|
#70 | |
|
Senior Member
Join Date: Feb 2011
Posts: 1,487
Likes: 531
Liked 1,010 Times in 506 Posts
Mentioned: 486 Post(s)
Tagged: 0 Thread(s)
|
Thank you for everything, I want to donate you some money, do you have paypal?[/QUOTE]yes but as the 3.55 install has not been done correctly yet you need to de-hash now then update to rogero 3.55 cfw then update to rogero 4.30 dont go directly to another firmware untill you have done the dehash as there is no telling what state your syscon is in atm |
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
|
|
