[baileyscream]

Originally Posted by dubeyduck ok but now when i try it i try to flash it how you sed to do it i get the error 1 1 0 0 1 0 0 0 and this is wot it says in the flasher log start logging... One Key downgrade mode. start checking...OK. metldr not supported but i dont no me ps3 is a chec2003a DYN-001 board thanks for trying help

re install the E3 update
re-sit the clip and connector on the E3 board

if your soldering the linker check the wires are not shorting anywhere or wires have detached
(sorry somany ppl now that i have forgotton if you used clip or linker)

[dubeyduck]

Originally Posted by baileyscream re install the E3 update re-sit the clip and connector on the E3 board if your soldering the linker check the wires are not shorting anywhere or wires have detached (sorry somany ppl now that i have forgotton if you used clip or linker)

the **** clip mate do you mean update the the flasher itself thanks

[baileyscream]

Originally Posted by rika85 That's what I thought as well, however I did mange to overcome that problem. Anyway, have a good nipping. Yes when you get up, please do check them. regards

no i mean i'm going out for 10 min
nipping out / popping out / going out lol
************* [ - Post Merged - ] *************

Originally Posted by dubeyduck the **** clip mate do you mean update the the flasher itself thanks

yep use the multi console update again.
its just incase it didnt go on right.

[dubeyduck]

Originally Posted by baileyscream no i mean i'm going out for 10 min nipping out / popping out / going out lol ************* [ - Post Merged - ] ************* yep use the multi console update again. its just incase it didnt go on right.

i still get that error or the one about the clip not been on correct

[rika85]

Originally Posted by dubeyduck i still get that error or the one about the clip not been on correct

Well, my bad. I thought you meant taking a nap. Well did you manage to check them please?

[baileyscream]

Originally Posted by rika85 Well, my bad. I thought you meant taking a nap. Well did you manage to check them please?

ok first dump is good
second dump has alot wrong with it

give me a min to read back and see where we are
then i can advise you
************* [ - Post Merged - ] *************

Originally Posted by dubeyduck i still get that error or the one about the clip not been on correct

remove the clip and clean the legs on the nor and the pins inside the clip with alcohol wipes or something simular

(its late so sorry for any bad spelling lol)
************* [ - Post Merged - ] *************

Originally Posted by rika85 Well, my bad. I thought you meant taking a nap. Well did you manage to check them please?

right
wrong lv2diag used to exit fsm.
that explains the test dump having alot missing

right put the origional dump on the sd card with nothing else

switch 1 up
switch 2 / 3 / 4 / 5 down
switch 6 up

turn ps3 on wait 10 - 20 sec
press start

fingers crossed it finnishes with no error

if it finnishes with no error then click the reset on the front of the E3 then click start again (this will ensure all the dump is wrote. )

if it errors then re-seat the clip tnd try again.

[rika85]

Originally Posted by baileyscream ok first dump is good second dump has alot wrong with it give me a min to read back and see where we are then i can advise you ************* [ - Post Merged - ] ************* remove the clip and clean the legs on the nor and the pins inside the clip with alcohol wipes or something simular (its late so sorry for any bad spelling lol)

By the first dump you mean the one that I sent you 2-3 days ago? if thats so then why did it brick then? and the second dump the one I sent to you earlier 2day was the one after bricking, isn't it normal to have a lot of wrongs in it?

Ok now please tell me what the next step would be? I downgraded the ps3 and installed rogero, but then it did not go out of service mode although I put your Lev2 in. Then I tried to put other Lev2s in there I mean random ones. Then it got bricked.

Now I think I shout somehow fix the brick then try to get it out of factory service mode. I don't know how though LOL.

Edit: I missed your timing again. LOL
************* [ - Post Merged - ] *************
baileyscream, shall I connect the hard drive in it then the process or is the hdd not needed? (I did put the hdd in it all the time before)?

[dubeyduck]

it still didnt work i think the clip is Brock iv tried to fit it about 50 time and keep getting the error for the clip not connecting im just going to to solder it to the linker tomorrow thanks for all your help

Originally Posted by baileyscream remove the clip and clean the legs on the nor and the pins inside the clip with alcohol wipes or something simular (its late so sorry for any bad spelling lol)

[baileyscream]

Originally Posted by rika85 By the first dump you mean the one that I sent you 2-3 days ago? if thats so then why did it brick then? and the second dump the one I sent to you earlier 2day was the one after bricking, isn't it normal to have a lot of wrongs in it? Ok now please tell me what the next step would be? I downgraded the ps3 and installed rogero, but then it did not go out of service mode although I put your Lev2 in. Then I tried to put other Lev2s in there I mean random ones. Then it got bricked. Now I think I shout somehow fix the brick then try to get it out of factory service mode. I don't know how though LOL. Edit: I missed your timing again. LOL ************* [ - Post Merged - ] ************* baileyscream, shall I connect the hard drive in it then the process or is the hdd not needed? (I did put the hdd in it all the time before)?

first dump was the good one (the one you sent the other day)
you dont put the hdd in as the tristate is set to gnd (flash fun) so the ps3 wont boot or try to read from hdd

dont you dare try fsm yet

as soon as you do the double flash let me know
************* [ - Post Merged - ] *************

Originally Posted by dubeyduck it still didnt work i think the clip is Brock iv tried to fit it about 50 time and keep getting the error for the clip not connecting im just going to to solder it to the linker tomorrow thanks for all your help

i thought you had gone to bed

it can still be the connector on the E3 board
if you have a small clamp like a small quick clamp or a big clothes peg try clamping the clip on the E3 board as that can get loose so stupidly easy.

[dubeyduck]

Originally Posted by baileyscream first dump was the good one (the one you sent the other day) you dont put the hdd in as the tristate is set to gnd (flash fun) so the ps3 wont boot or try to read from hdd dont you dare try fsm yet as soon as you do the double flash let me know ************* [ - Post Merged - ] ************* i thought you had gone to bed it can still be the connector on the E3 board if you have a small clamp like a small quick clamp or a big clothes peg try clamping the clip on the E3 board as that can get loose so stupidly easy.

im going in a min mate lol the peg thing didn't work and its not going work now cause iv just got pissed off with it and ripped the clip it in half lol so il solder the link on tomorrow i should of done that in the first place and il let you no how it goes on and nice one for all your help i appreciate it