[denis-str]

YOUR DUMP IS NOT VALID, FLOWREBUILDER SHOWS ERROR WHILE EXTRACTING YOUR DUMP
it is impossible to restore the console ?

[Sasuke1981]

I got. A big problem guys i hope You can Help me out ....i bricked my ps3 during The restore process with e3 cause i flashed with a bad dump ( Yes i'm stupid) now i'm lucky that i Made many backups and found 2 that are identical and after checks They are good ( i Made them check by others also) now i soldered nor tristate and a GND point to make ps3 lights up...flashed with right backup but i still get black screen with no signal and no hd activity...any idea what i'm doing Wrong?

[noobzega]

Originally Posted by denis-str YOUR DUMP IS NOT VALID, FLOWREBUILDER SHOWS ERROR WHILE EXTRACTING YOUR DUMP it is impossible to restore the console ?

Without good valid dump I think its not possible. @playerkp420 @baileyscream
************* [ - Post Merged - ] *************

Originally Posted by Sasuke1981 I got. A big problem guys i hope You can Help me out ....i bricked my ps3 during The restore process with e3 cause i flashed with a bad dump ( Yes i'm stupid) now i'm lucky that i Made many backups and found 2 that are identical and after checks They are good ( i Made them check by others also) now i soldered nor tristate and a GND point to make ps3 lights up...flashed with right backup but i still get black screen with no signal and no hd activity...any idea what i'm doing Wrong?

First are you 100% sure you have good valid dump from your PS3? If you have good valid dump I will help you to fix it in next few hours need to go in town right now.

[baileyscream]

Originally Posted by denis-str YOUR DUMP IS NOT VALID, FLOWREBUILDER SHOWS ERROR WHILE EXTRACTING YOUR DUMP it is impossible to restore the console ?

have you flashed anything to the ps3?
if no then remove the clip and re-attach it.
clamp the clip down and do another dump.
validate it.
if its good then get a second opinion.
if its bad re-do the clip again.

if you are soldering wires then re-do all the wires.
take your time and use flux.
then re-do a dump
validate it
if its good then get a second opinion
if its bad re-do the wires again.

if you have flashed then do one of the above and when you get a second opinion put a link to this thread and say your trying to recover from flashing a bad dump.
************* [ - Post Merged - ] *************

Originally Posted by Sasuke1981 I got. A big problem guys i hope You can Help me out ....i bricked my ps3 during The restore process with e3 cause i flashed with a bad dump ( Yes i'm stupid) now i'm lucky that i Made many backups and found 2 that are identical and after checks They are good ( i Made them check by others also) now i soldered nor tristate and a GND point to make ps3 lights up...flashed with right backup but i still get black screen with no signal and no hd activity...any idea what i'm doing Wrong?

get the dump you have flashed to the ps3 (the one you say is good)
open it in hxd
go to 200
does it say IFI or FI.I ?

[Sasuke1981]

It says FI.I ...btw is really The same that i soldered nor tristate to a GND point instead of sbe on clip? Cause i read that is The same but i dunno for sure cause this is my first brick

I checked my 2 dump with an hex editor and they are identical...plus with flowrebuilder and they seems ok...do i need to send them here for a check? You are indeed more qualified than me

[noobzega]

Originally Posted by Sasuke1981 It says FI.I ...btw is really The same that i soldered nor tristate to a GND point instead of sbe on clip? Cause i read that is The same but i dunno for sure cause this is my first brick I checked my 2 dump with an hex editor and they are identical...plus with flowrebuilder and they seems ok...do i need to send them here for a check? You are indeed more qualified than me

If you have brick issue and your ps3 power on, no video, hdd and usb activity, now when its soldered you can use tut i post and you will unbrick your ps3 I'm sure you will.
************* [ - Post Merged - ] *************

Originally Posted by Sasuke1981 I got. A big problem guys i hope You can Help me out ....i bricked my ps3 during The restore process with e3 cause i flashed with a bad dump ( Yes i'm stupid) now i'm lucky that i Made many backups and found 2 that are identical and after checks They are good ( i Made them check by others also) now i soldered nor tristate and a GND point to make ps3 lights up...flashed with right backup but i still get black screen with no signal and no hd activity...any idea what i'm doing Wrong?

You mean restore procces after you make dump 1 down, 2 down, 3 up, 4 down, 5 down, 6 down, and then you turn all down and flash back your dump? Why would you do that?

[haz367]

the only differents between GND vs SBE point on e3ribbon/or the alternate point at the back of the e3, is that with the SBE point u don't need to remove the wire, flip IF u leave the E3 inthere... the first switch back from Flash fun to normal ps3 mode and the PS3 boots as normal, with Tristate to any GND point on motherboard u have to remove/cut the wire from GND or else the PS3 keeps halting in Tristate mode, i'm sure it's called something else anyway....u can't do anything else with GND wire connected.... only dump/reflash from it, remove the gnd wire after succesfull flash to boot normal into XMB again

the black screen after restoring/flashing the clean/valid dump, try flashing it 2 times in a row, people seem to have the "black screen" fixed after flashing the same dump twice

Originally Posted by Sasuke1981 It says FI.I ...btw is really The same that i soldered nor tristate to a GND point instead of sbe on clip? Cause i read that is The same but i dunno for sure cause this is my first brick

[noobzega]

Originally Posted by haz367 the only differents between GND vs SBE point on e3ribbon/or the alternate point at the back of the e3, is that with the SBE point u don't need to remove the wire, flip IF u leave the E3 inthere... the first switch back from Flash fun to normal ps3 mode and the PS3 boots as normal, with Tristate to any GND point on motherboard u have to remove/cut the wire from GND or else the PS3 keeps halting in Tristate mode, i'm sure it's called something else anyway....u can't do anything else with GND wire connected.... only dump/reflash from it, remove the gnd wire after succesfull flash to boot normal into XMB again the black screen after restoring/flashing the clean/valid dump, try flashing it 2 times in a row, people seem to have the "black screen" fixed after flashing the same dump twice

Try flash 2 times your valid dump in flasfun mode, if you dont get your PS3 boot into XMB PM me.

[Sasuke1981]

Thats Why it give me black screen then....i'll tra CUT The wire then...cause after flashfun i just power off The ps3 ( without The power cable) and then power on The ps3 ...

I CUT The wire..ps3 is turning on without shut off like before...but still black screen with no video signal or hd activity any idea?

Yes noobzega ...that restore process...in e3 Official video say it need to be' done :/ ...its not necessary?

[haz367]

well if it stays on now with wire cut and black screen and u sure the dump is valid then reflash the same dump once again, is it a 355 dump? then try trigger FSM mode and install rogero 3.7 from it.....other guys have it fixed..same black screen issue..reflash it and see if it boots first to XMB or something, rogero 3.7 is the PUP to install on such bricks...goodluck

always try first ur own stuff before messing with prohacks dump, just make sure ur own backup from that PS3 is valid cuse if not and using prohack..its perm-bricked

don't take my word for it..just trying to help

edit: and restore ISN'T REQUIRED, can't hurt to do it IF the made dump is VALID before doing restore, i was one of them that bricked also there because of it..lucky it was bad clip conn only but normally the restore isn't required to get a succesfull "downgrade"