[man ineed help]

I use an e3 flasher (clip) and my ps3 got bricked. i attempted to reflash bios but during the process something went wrong everytime but then i reseated the clip and it went fine. however, on the dongle steps i noticed my usb ports seemed to have no power. By the way i soldered vss to ground on my mobo or something like that to keep it on because it didnt want to stay on at first. Any help is appreciated and if any other info is needed please let me know! Thanks

Also my power button does nothing. I have to unplug it to turn it off, and i have no video or audio. It just stays on. I already attempted removing the clip and e3 flasher but same thing.

[jhax78]

did you verify the dump before flashing anything to the ps3?

[Mr.Dutch]

Originally Posted by man ineed help By the way i soldered vss (tristate?) to ground on my mobo or something like that to keep it on because it didnt want to stay on at first. ....Also my power button does nothing. I have to unplug it to turn it off, and i have no video or audio. It just stays on. I already attempted removing the clip and e3 flasher but same thing.

still have the tristate soldered to ground, this will halt the system, so no video or audio is probably expected....

you not by any chance damaged the ribbon cable from mainboard to power/eject board?, they seem to be brittle...

also mention your ps3 model and mainboard number (like JSD-001)

[man ineed help]

No i haven't damaged the ribbon cable to the power/eject button. SN:CECH-2501A
MOBO IS JTP-001
************* [ - Post Merged - ] *************

Originally Posted by jhax78 did you verify the dump before flashing anything to the ps3?

No i haven't verified the dumps. how can i do that?
************* [ - Post Merged - ] *************
also this might help but i soldered vss>ground not tristate>ground because i couldnt solder the point on the e3 ribbon. So probably the points i soldered are halting the system. sorry guys the power button does turn off the system but i need to hold it for about 20 secs. :/

[Mr.Dutch]

Originally Posted by man ineed help also this might help but i soldered vss>ground

technically vss is ground, so you soldered a wire from ground to ground?

without the wire you have the classic ylod?

@baileyscream probably knows how to help you better.

EDIT:, ooh wait, you probably broke a fuse.

[baileyscream]

Originally Posted by man ineed help I use an e3 flasher (clip) and my ps3 got bricked. i attempted to reflash bios but during the process something went wrong everytime but then i reseated the clip and it went fine. however, on the dongle steps i noticed my usb ports seemed to have no power. By the way i soldered vss to ground on my mobo or something like that to keep it on because it didnt want to stay on at first. Any help is appreciated and if any other info is needed please let me know! Thanks Also my power button does nothing. I have to unplug it to turn it off, and i have no video or audio. It just stays on. I already attempted removing the clip and e3 flasher but same thing.

you have soldered trist or sbe to gnd
this is halting the ps3 so you can flash or dump the ps3.

what guide have you followed
how far did you get on the guide
did you get your dump double checked
************* [ - Post Merged - ] *************

Originally Posted by man ineed help also this might help but i soldered vss>ground not tristate>ground because i couldnt solder the point on the e3 ribbon.

can you tell me what points are soldered to what on the below diagram





wait a min

Originally Posted by jhax78 did you verify the dump before flashing anything to the ps3? No i haven't verified the dumps. how can i do that?

fool !!!!
damn fool !!!!!!

[man ineed help]

ok i verified my dumps with e3 nor dump checker. and good news i removed the wire i soldered and now it actually shows video. my usb ports have power again also. but when it turns on it says " cannot start. correct hard disk was not found" Any ideas how to fix this?
i tried to go into safe mode when u hold the power button for 2 beeps but it doesnt enter safe mode. it just continues to tell me the same thing

[noobzega]

Where is your HDD located now?

[man ineed help]

Originally Posted by noobzega Where is your HDD located now?

i still have it in the esata station with the e3 flasher

[playerkp420]

Originally Posted by man ineed help i still have it in the esata station with the e3 flasher

Press the button on the back of the esata station. It is called POWER. A light will magically appear, and the drive will have power. Then as long as you have the esata cable connecting it to the flasher, that is plugged into the hdd slot. You will be good.