[Sasuke1981]

the dump dont think is a 3.55 cause i made a restore before doing downgrade process...so the dump is 4.30...i made some backups (5) and used the wrong one ofc for the restore process and then brick...lucky that i have found 2 of the dumps should be good and i'm trying to debrick this bastard thats all...the dumps are clean..i just used hex editor and reflow builder for check them...but apart that i didnt patched anything

[haz367]

fingers crossed here hope u get it fixed somehow..with good/valid dumps it should..but nvm my post about Rogero 3.7/FSM if the dumps are 4.30 ofcourse...if it's ofw4.30/or if coreos is corrupt ONLY! u could patch it with 355coreos and flash and it gives the "connect controller" and finish the downgrade....better leave it to the pro's cuse not all bricks the same...and i'm gonna guess at it anyway..

[noobzega]

Thats true

[haz367]

yup..glad u agree...

[Sasuke1981]

Hope to not have a permabrick...

[ortis123]

Originally Posted by noobzega Try flash 2 times your valid dump in flasfun mode, if you dont get your PS3 boot into XMB PM me.

could you give me a prohack custom dump link??

[haz367]

http://www.ps3hax.net/showthread.php?t=30738

[deanclaxton]

Originally Posted by noobzega Ok since lot people brick PS3 when they try to downgrade I will try to help anyone who have same problem. So first if you brick your PS3 dont open new thread "I brick PS3, please help" just post your problem here. Let's start. 1. Make sure you have good valid dump from your PS3 before you even try to go on downgrade. 2. When you make your dump from PS3 please send it here http://www.ps3hax.net/showthread.php?t=48432 so guys can check it. 3. Once you have good valid dump from your console please let me know if you brick your console and I will help you, via gmail, via facebook, or here on PS3 hax. Just remeber you need to have good valid dump from your PS3 that is bricked. @tanimr2002 is first guy I helped him to solve his brick problem.

Hi,

I have a 40GB console that was bricked when my son attempted to downgrade firwmware using factory service mode and a downgrade pup file (I think this is what happened).

Original symptom was the console turned on (green light), yellow light, beeped 3 times and turned off (red light).

I used infectus to dump the nand, and have found lots of corruption.

I've repaired the flash region table manually, and then patched the file to replace the coreos files with those in the ultimate downgrade tutorial.

I can now rescramble with flowrebuilder. If I unscramble my current nand files I get no bad blocks and all the files extract out with correct lengths.

I think though that my revokation package is corrupted. This is a per os region in flash, and therefore I should be able to replace it with the same data from a good console?

Do you have a nand dump from a sem-001 console that I could get hold of to repair my own? Would have to be 3.55 firmware.

When I write my current nand images out to nand and test in the console, I now get a solid green light but no beeps, no usb power, no image - nothing. Have to switch off by pulling the power. Progress of sorts but not there yet!

[versatilegames]

Hi,
Just faced a "bricked" issue (may be) downgrading from 4.21 to Rogero 4.3 V 2.05. I installed the clip and updated it with the samsung update. Next I successfully backed up the bios and do have a verified valid dump, http://www.ps3hax.net/showthread.php...d=1#post519691
Then I began the "Restore" process and everything got messed up. I encountered the error 10001111 "Failed to write PS3 BIOS". There after I cannot switch on my console. Every time I press the switch I see the green light and then it shuts down immediately and there is not red or yellow light visible at all, the console simply turns off as if no power is connected to it. Then I need to press the switch once to see the red light and then one more time to see the green light followed by an immediate shut down. Some say that the console is bricked and I need to get the clip solder to the motherboard. I am looking for a second advice here since I have never tried the soldering thing. Please advice me to unbrick my console.
Thanks.

[playerkp420]

Originally Posted by versatilegames Hi, Just faced a "bricked" issue (may be) downgrading from 4.21 to Rogero 4.3 V 2.05. I installed the clip and updated it with the samsung update. Next I successfully backed up the bios and do have a verified valid dump, http://www.ps3hax.net/showthread.php...d=1#post519691 Then I began the "Restore" process and everything got messed up. I encountered the error 10001111 "Failed to write PS3 BIOS". There after I cannot switch on my console. Every time I press the switch I see the green light and then it shuts down immediately and there is not red or yellow light visible at all, the console simply turns off as if no power is connected to it. Then I need to press the switch once to see the red light and then one more time to see the green light followed by an immediate shut down. Some say that the console is bricked and I need to get the clip solder to the motherboard. I am looking for a second advice here since I have never tried the soldering thing. Please advice me to unbrick my console. Thanks.

LOL.

I just answered you here.

I guess you do not want my help.

Good luck.