[KuroiKami2013]

Originally Posted by playerkp420 You may already be in FSM then. Put the Lv2diag.self and the PS3UPDAT.pup on the root of your fat32 formatted USB. Put it in the right USB port, power on PS3 and wait.

it will be on4.31 fsm. is that ok?

[playerkp420]

Originally Posted by KuroiKami2013 problem is when i patch my dump and reflash the patched dump. the ps3 turn on for a bit then turn off. what do i do from there?

Originally Posted by KuroiKami2013 it will be on4.31 fsm. is that ok?

You said you patched and flashed your patched dump. The patches allow for FSM firmware install.
If the console has been flashed with the patched dump, and is in FSM, and you don't have USB with Lv2diag.self to call what function you want, it will shut off when it can't find it.

Put the files I linked on the root of your fat32 formatted USB. Put the USB in the right port and turn the PS3 on. If it starts installing the firmware, then that was your problem. Make sure the hdd is connected when you do it.
If it just shuts off again, that means:
1. You flashed a non valid dump and bricked. To fix solder the wire to keep the ps3 on and flash a patched valid dump.
2. Your clip or soldering is not correct, so the flashing did not flash correctly. To fix, solder the wire to keep the ps3 on and reseat the clip or correct the soldering.

[haz367]

thx for confirm playerkp420, i was sure it goes off when u trigger FSM at this stage(after downgrade) and try to boot the PS3, it goes off, so yeah i guess he was on the right track and just needed to install the PUP from FSM using enter lv2diag.self, let's hope its that or else if he got a valid one...restore it or else first redump..redump until u have good one(per console keys) and just patch (COREOS) again like usual

Originally Posted by playerkp420 If the console has been flashed with the patched dump, and is in FSM, and you don't have USB with Lv2diag.self to call what function you want, it will shut off when it can't find it..

[KuroiKami2013]

Originally Posted by playerkp420 You said you patched and flashed your patched dump. The patches allow for FSM firmware install. If the console has been flashed with the patched dump, and is in FSM, and you don't have USB with Lv2diag.self to call what function you want, it will shut off when it can't find it. Put the files I linked on the root of your fat32 formatted USB. Put the USB in the right port and turn the PS3 on. If it starts installing the firmware, then that was your problem. Make sure the hdd is connected when you do it. If it just shuts off again, that means: 1. You flashed a non valid dump and bricked. To fix solder the wire to keep the ps3 on and flash a patched valid dump. 2. Your clip or soldering is not correct, so the flashing did not flash correctly. To fix, solder the wire to keep the ps3 on and reseat the clip or correct the soldering.

thanks for helping.

my dump is valid since i checked it. and when i flashed back my good dump it went to ofw 4.31 fsm.

i try to patch it then use rogero. reply here as soon as i find something.

[donkey-punch]

Originally Posted by KuroiKami2013 thanks for helping. my dump is valid since i checked it. and when i flashed back my good dump it went to ofw 4.31 fsm. i try to patch it then use rogero. reply here as soon as i find something.

you need to elaborate who's guide you are following. You can't just flash your original dump without the e3downgrade.bin on the sd card with your dump. Or you either have to patch your dump. Flashing back an unpatched dump without the downgrade.bin will just put you back to the start.

[KuroiKami2013]

Originally Posted by donkey-punch you need to elaborate who's guide you are following. You can't just flash your original dump without the e3downgrade.bin on the sd card with your dump. Or you either have to patch your dump. Flashing back an unpatched dump without the downgrade.bin will just put you back to the start.

i first followd the khaledo guide on youtube. then after that it gone chaos.

i got 2 ps3. 1 is my friend and one is my own. my own i think it's pretty dead. i got a good dump after solder. i reflashed, but the ps3 start up everything, but nothing shows up on television.

my friends ps3 is stuck at ofw 4.31 fsm i reflashed my original dump restore to its original.


sorry i am so stressed and kind of losing my mind


if i patched the dump and reflash it to ps3

i start the downgrade prosess. do i need to do the eject+power first or just insert usb with pup and lv2 file?
************* [ - Post Merged - ] *************

Originally Posted by playerkp420 You said you patched and flashed your patched dump. The patches allow for FSM firmware install. If the console has been flashed with the patched dump, and is in FSM, and you don't have USB with Lv2diag.self to call what function you want, it will shut off when it can't find it. Put the files I linked on the root of your fat32 formatted USB. Put the USB in the right port and turn the PS3 on. If it starts installing the firmware, then that was your problem. Make sure the hdd is connected when you do it. If it just shuts off again, that means: 1. You flashed a non valid dump and bricked. To fix solder the wire to keep the ps3 on and flash a patched valid dump. 2. Your clip or soldering is not correct, so the flashing did not flash correctly. To fix, solder the wire to keep the ps3 on and reseat the clip or correct the soldering.

the ofw 4.31 is not patched dump.

I failed when the screen Off connecting controller, didnt find my dongle so connected controler and triede i don update through usb. It bricked then i recovered with my original good valid dump. This is where i dont know what to do next please help me

[KuroiKami2013]

My own console is dead. Dont want to fail my friends either

[playerkp420]

Originally Posted by KuroiKami2013 My own console is dead. Dont want to fail my friends either

Follow the guide below. Stay away from that Khalkadeon video.

[KuroiKami2013]

Originally Posted by playerkp420 Follow the guide below. Stay away from that Khalkadeon video.

Should i just proceed while on ofw 4.31fsm？

[donkey-punch]

Originally Posted by KuroiKami2013 i first followd the khaledo guide on youtube. then after that it gone chaos. i got 2 ps3. 1 is my friend and one is my own. my own i think it's pretty dead. i got a good dump after solder. i reflashed, but the ps3 start up everything, but nothing shows up on television. my friends ps3 is stuck at ofw 4.31 fsm i reflashed my original dump restore to its original. sorry i am so stressed and kind of losing my mind if i patched the dump and reflash it to ps3 i start the downgrade prosess. do i need to do the eject+power first or just insert usb with pup and lv2 file? ************* [ - Post Merged - ] ************* the ofw 4.31 is not patched dump. I failed when the screen Off connecting controller, didnt find my dongle so connected controler and triede i don update through usb. It bricked then i recovered with my original good valid dump. This is where i dont know what to do next please help me

You can't use your dump to unbrick your friends console.