[KuroiKami2013]

I bricked it during process of the youtube guide of e3 homepage link. Solder and got valid dump. Reflash started up but the hdd usb seems not reading power keep being on and i need to pull cable or hold power to shut off what to do?

Seems like the process file i use was bad non valid dump. Since i didnt knew you had to dump many times

[MJ999]

Be specific buddy.

You followed Khalkedon's tutorial ?

Do you have a valid dump ?

[KuroiKami2013]

Originally Posted by MJ999 Be specific buddy. You followed Khalkedon's tutorial ? Do you have a valid dump ?

yes
and yes but only after i soldered and dumped through flashfun and backup function.


but from the

statistics the right side is off by value 1 or else everything seems ok.

[haz367]

Khalkedon's tutorial isn't bad except for not showing proper validating before he restores the dump...wich ISN'T REQUIRED, but it can't hurt either IF THE DUMP IS PERFECTLY VALID that's all, so yeah in that pway it's a BAD GUIDE for beginners!......the FF percentages could be just COREOS>ROS0/1=firmware on flash being corrupt, if that is the case just patch it with the E3 manual downgrade 355 COREOS patches...check the percentages again also newer 4.xx have different percentages but that part must be already edited at the wiki..correct...just for fun try checking a REBUG 4.21.2 if u got any..and check the percentages..they are way of what the wiki shows..although correct cuse it's hugely patched making it the kickass CFW it is and ofcourse VALID to....


and finally some info/fixes u can try for the HDD no activity = NO BRICK!

http://www.ps3devwiki.com/wiki/E3#Bl....28no_brick.29

ignore the "dual boot" as that is not the case on ur end..anyway it shows some options u can try to get it running again

Blackscreen with no hdd activity and only hard reset possible (no brick)

    remove clip and try again
    try getting into FSM with a faster power/eject combo
    if you manually patched, check if you did not patch the byte-reversed copy
    attempt flashfun downgrade
    resolder SBCE -> A / cut A/B properly  (dual boot)
    restrip contacts on the backside of the E3 Flasher (they must not touch the metal casing) they have to be isolated very good .. they are very sensitive and cause a lot of errors
    if the E3 flasher is not connected, also ALWAYS disconnect the clip otherwise blackscreen because of A/B Cut .. (dual boot)

In case your usb ports are still working:

    3.55 ONLY: use the rsod/brickfix lv2diag in Service Mode (helped my system a lot .. it booted to blackscreen 8/10 times; after using lv2diag 2/10 times)
    if using TBv2 please note, that instead of proper security they used loops to protect their product; try reinstalling the FW via recovery mode
    also dont use custom boot logos with TBv2 !!
    Reinstall a downgrader prepatched FW 

    if you have no success with the methods from above solder Tri/SBE and reflash a valid backup via flash fun mode (100000)

[Mr.Dutch]

Originally Posted by KuroiKami2013 stuck used e3

@stuck? , did you?

[stuck?]

Originally Posted by Mr.Dutch @stuck? , did you?

When I saw this thread show up on my homepage I thought it was another story created by yourself.

[KuroiKami2013]

Originally Posted by haz367 Khalkedon's tutorial isn't bad except for not showing proper validating before he restores the dump...wich ISN'T REQUIRED, but it can't hurt either IF THE DUMP IS PERFECTLY VALID that's all, so yeah in that pway it's a BAD GUIDE for beginners!......the FF percentages could be just COREOS>ROS0/1=firmware on flash being corrupt, if that is the case just patch it with the E3 manual downgrade 355 COREOS patches...check the percentages again also newer 4.xx have different percentages but that part must be already edited at the wiki..correct...just for fun try checking a REBUG 4.21.2 if u got any..and check the percentages..they are way of what the wiki shows..although correct cuse it's hugely patched making it the kickass CFW it is and ofcourse VALID to.... and finally some info/fixes u can try for the HDD no activity = NO BRICK! http://www.ps3devwiki.com/wiki/E3#Bl....28no_brick.29 ignore the "dual boot" as that is not the case on ur end..anyway it shows some options u can try to get it running again Blackscreen with no hdd activity and only hard reset possible (no brick) remove clip and try again try getting into FSM with a faster power/eject combo if you manually patched, check if you did not patch the byte-reversed copy attempt flashfun downgrade resolder SBCE -> A / cut A/B properly (dual boot) restrip contacts on the backside of the E3 Flasher (they must not touch the metal casing) they have to be isolated very good .. they are very sensitive and cause a lot of errors if the E3 flasher is not connected, also ALWAYS disconnect the clip otherwise blackscreen because of A/B Cut .. (dual boot) In case your usb ports are still working: 3.55 ONLY: use the rsod/brickfix lv2diag in Service Mode (helped my system a lot .. it booted to blackscreen 8/10 times; after using lv2diag 2/10 times) if using TBv2 please note, that instead of proper security they used loops to protect their product; try reinstalling the FW via recovery mode also dont use custom boot logos with TBv2 !! Reinstall a downgrader prepatched FW if you have no success with the methods from above solder Tri/SBE and reflash a valid backup via flash fun mode (100000)

my ps3 base is under 3.55 i checked with minimum firmware.

true what you said. i must reflash with bad valid. but i somehow got a god dump after i solder and dumped through flashfun ?

i tried to reflash the good dump but the ps3 start on infinity no hdd activity neither the usb port works.


my ffh s 9.34 where i read it should be around 10.42+ or else everything is in valid point (checked with HxD)

i could even extract it the bin get bootldr and so on

what should i do next ? thanks for answering

[haz367]

nvm.............

[KuroiKami2013]

Originally Posted by haz367 nvm.............

so what should i do ?

[haz367]

don't know man...i'm sure the others can help u...u are making much topics..its hard to keep up...and after u make new topic...u post in another its fixed..right....i can't help i'm sorry..