[xonsox]

consol CECHG04
board sem-001
dumps ok
when write, always verification fail

Progskeet 1.1 + clip

some idea?

[Sarah1331]

Originally Posted by xonsox consol CECHG04 board sem-001 dumps ok when write, always verification fail Progskeet 1.1 + clip some idea?

Yep the clip


Sent from my iPhone 5 using Tapatalk

[furtsiv]

hi
can anyone tell me what dongles use the atmel1286 chip i need it to build teensy++

[magic_marty]

might not be the best place to ask but can i connect my ps3 to my laptop using blue-tooth? i tried but it doesn't find it when searching for connections..is there something different i need to do or is it just not possible?

thanks all...
<Marty>

[sREa]

Originally Posted by Sarah1331 Yes you can downgrade

Ty, so know some place that can help me? The "best" shop here denies everything.

EDIT
Forgot to mention it's a CECHC

[jensen76]

Originally Posted by baileyscream try the latest (NAND only comfirmed working) one ProgSkeet 1.2 Bitstream [121106.2121] from HERE before you update the bistream flash your checked dump back to the ps3 and check it boots / works propperly. now you need to update to the new bitstream and do freash dumps to make sure its working correctly. when you merge the two dumps together with flow rebuilder do a compare against your known good dump to check its the same. and the top bottom nands. if you dump the two nands and call one of them DUMP A and the other DUMP B (remember which is which nand) then select one as top the other as bottom in flow rebuilder and if its the wrong way round then it will tell you. let me know which is top and bottom when you have done this and i will add this into my guide. @Sarah1331 did tell me about this and told me which was which on different boards but i just cannot find that post to add it in. so my own fault. sorry to everyone that has had a problem here due to this ************* [ - Post Merged - ] ************* do as i have told jensen above

tryed that and everything is the same.dumps are all the same...

only thing i can try is new usb stiks.. there is 1 bad block on cpu side so im giving op now.dont know how to fix it.the consol works fine when i flash stock nands back.only thing i cant get i to do is read the pup fil in service mode.tryed 5 usb stiks,3 harddrives.nothing is working.

here are the nands on CECHG04 sem-001

[daveyaz]

Hi...
i got e3 flasher
i followes this guide and was success downgrade phat ps3...

now i did the same on slim ps3 cech2504A...
i did a flash dump
i checked it my self,,,looks good and valid
i uploaded my dump for checking and was told here it is valid.
i used one key downgrade by E3....lights stopped flashing...lights started ligh one by one,,,and suddenly lights was flashing....i press stop....tried again....now my ps3 power on for 2 seconds then power off...power light is off...but if i press it it tyrns red and once again i press it,,it powers up for 2-3 seconds and power off ?!?!!?

any idea...PLEASE

[baileyscream]

E3 guide updated
the patching with flowrebuilder was telling ppl to use the origional dump instead af the bytereversed dump
all fixed now
thanks @haz367 for the heads up
************* [ - Post Merged - ] *************

Originally Posted by daveyaz Hi... i got e3 flasher i followes this guide and was success downgrade phat ps3... now i did the same on slim ps3 cech2504A... i did a flash dump i checked it my self,,,looks good and valid i uploaded my dump for checking and was told here it is valid. i used one key downgrade by E3....lights stopped flashing...lights started ligh one by one,,,and suddenly lights was flashing....i press stop....tried again....now my ps3 power on for 2 seconds then power off...power light is off...but if i press it it tyrns red and once again i press it,,it powers up for 2-3 seconds and power off ?!?!!? any idea...PLEASE

can you cut and paste the txt file that would have been on the sd card when you tried to do the patch.

you will now need to solder sbe on the ribbon to the sbe on the board.
see the soldering section in the guide for the sbe point
then have flashfun switch up while doing the downgrade patch again.

but post that txt file first
************* [ - Post Merged - ] *************

Originally Posted by jensen76 tryed that and everything is the same.dumps are all the same... only thing i can try is new usb stiks.. there is 1 bad block on cpu side so im giving op now.dont know how to fix it.the consol works fine when i flash stock nands back.only thing i cant get i to do is read the pup fil in service mode.tryed 5 usb stiks,3 harddrives.nothing is working. here are the nands on CECHG04 sem-001

i will sleep on this ang get back to you tomorrow.
dont be thinking i have forgotten about you

[jensen76]

Originally Posted by baileyscream i will sleep on this ang get back to you tomorrow. dont be thinking i have forgotten about you

thank you i have sent you a komplite file whit my dumps if you need to check anything... thanks

[daveyaz]

[QUOTE=[B]baileyscream[/B];524841][COLOR="Red"]E3 guide updated
************* [ - Post Merged - ] *************

can you cut and paste the txt file that would have been on the sd card when you tried to do the patch.

you will now need to solder sbe on the ribbon to the sbe on the board.
see the soldering section in the guide for the sbe point
then have flashfun switch up while doing the downgrade patch again.

but post that txt file first
************* [ - Post Merged - ] *************

Thanks...

Here is the txt file from the e3 flasher....

http://www.mediafire.com/?pcrolq9mctuki9kPlease Help me out....

Thanks again