[thegreatSalu]

@ baileyscream

In your guide you did not use a downgrade dongle, you suggested another method, is it ok?

another thing I am going upgrade my PS3's HDD to 2TB is it ok, will it work on E3 Flasher?

I am sorry but I'm going to buy E3 Flasher soon,so you might have answer my noob questions(If got anymore)

[baileyscream]

Originally Posted by thegreatSalu @ baileyscream In your guide you did not use a downgrade dongle, you suggested another method, is it ok? another thing I am going upgrade my PS3's HDD to 2TB is it ok, will it work on E3 Flasher? I am sorry but I'm going to buy E3 Flasher soon,so you might have answer my noob questions(If got anymore)

i do use a downgrade dongle. (fsm tool)
the ps3 wont see 2tb as far as i know. the max is 1tb

[Decoy]

Originally Posted by MJ999 I had this problem before, asked judges,he said check the wiring. After re-wiring BAM it worked.

worked hahaha! AT LAST! Thanks bailey for your guide and thanks MJ for helping :D! and ofcourse judges

[3absiso]

Originally Posted by Decoy worked hahaha! AT LAST! Thanks bailey for your guide and thanks MJ for helping :D! and ofcourse judges

Will i am happy for You Bro,
MY ProgSkeet V1.2 received a week ago and did not even open it

[Decoy]

@3absiso haha, dont open it its useless sadfully. but great now. teensy did the job in 24 Hours.

[baileyscream]

Originally Posted by daveyaz i got e3 flasher i followes this guide and was success downgrade phat ps3... now i did the same on slim ps3 cech2504A... i did a flash dump i checked it my self,,,looks good and valid i uploaded my dump for checking and was told here it is valid. i used one key downgrade by E3....lights stopped flashing...lights started ligh one by one,,,and suddenly lights was flashing....i press stop....tried again....now my ps3 power on for 2 seconds then power off...power light is off...but if i press it it tyrns red and once again i press it,,it powers up for 2-3 seconds and power off ?!?!!? any idea...PLEASE

Originally Posted by daveyaz Is there an answer....some nice guy here at the forum told me that i need to connect a wire between two points on the board and then continue downgrading as regular......

Originally Posted by daveyaz Is there a solution for this.........................????????????????? Thanks

solder sbe on the ps3 to sbe on the E3 ffc cable (found half way along the flex of the clip) find your board in the soldering section of the guide under "setting up E3" to see where the sbe point is
then do the patch part of the guide again with "flash fun" switch up. switches 2 3 4 5 down 6 up
it should take 10-15 minimum to flash.
once done turn off ps3 put "flash fun" down and see if ps3 turns on

[fudd69]

hi. I have a progskeet v1.2 that i just bought and I am having some difficulties installing the drivers. I am using a PC with installed Windows XP SP3. when i connect the progskeet to the PS3 to the PC it doesn' t recognize it and it says unknown device. then when i try to install the drivers from device manager it says "cannot continue the harware update wizard" and it fails. I had never used progskeet before and i have not understood if before using it on the PC i should do something else even if the person i bought it form told me that it was already programmed and ready to use.
thanks for your answers

[jensen76]

Originally Posted by fudd69 hi. I have a progskeet v1.2 that i just bought and I am having some difficulties installing the drivers. I am using a PC with installed Windows XP SP3. when i connect the progskeet to the PS3 to the PC it doesn' t recognize it and it says unknown device. then when i try to install the drivers from device manager it says "cannot continue the harware update wizard" and it fails. I had never used progskeet before and i have not understood if before using it on the PC i should do something else even if the person i bought it form told me that it was already programmed and ready to use. thanks for your answers

indstall the bitstream to progskeet first then you can indstall the driver...

[arloubas]

Originally Posted by fudd69 hi. I have a progskeet v1.2 that i just bought and I am having some difficulties installing the drivers. I am using a PC with installed Windows XP SP3. when i connect the progskeet to the PS3 to the PC it doesn' t recognize it and it says unknown device. then when i try to install the drivers from device manager it says "cannot continue the harware update wizard" and it fails. I had never used progskeet before and i have not understood if before using it on the PC i should do something else even if the person i bought it form told me that it was already programmed and ready to use. thanks for your answers

Assuming that the person you bought it from has already programmed it (you need Infectus programmer for this) then your slaveboard is most likely defective. I had the same problem; it even destroyed the USB ports of one of the laptops to which I connected it. My problem was that the regulator IC was short-circuited. Someone else (cannot recall his nickname) had the exact same problem and he posted in the Progskeet forum that there was a problem with a path just below the regulator IC and he somehow managed to correct it. Even better, a certain hard italian store can sell you the slaveboard only if you request it with an e-mail.

[fudd69]

thanks. but what' s the regulator IC? and what' s the Italian Store I can buy the slave board from.( i am italian so it should be good)