[unigsm]

my ps3 brickid

let switch 100000 and ps3 keep turn on.

put original backup and micro sd card press start button.

when flashing is done dont turn off ps3. change switch to 000001

take out and transfer e3downgrade.bin to micro sd card.

put back to tf card,press reset button then press start button

8 led ok ..e3flasher.log :
Program Nor OK.

My problem:
the 8 lights goes on one by one, but i dont have a signal on the tv

[saqibmush]

sbe point on my e3 ribbon were torn off so i soldiered from that sbe point on the e3-board to that point mentioned on the board ..this board and my consoles board is same.
is this a right way of using flash fun mode..?
please see the pic
iam unable to attach a pic here .so remove these (dot) n open the pic n tell me guz..

www(dot)mediafire(dot)com/view/?g6i553fb60kl80p

[3absiso]

Originally Posted by saqibmush sbe point on my e3 ribbon were torn off so i soldiered from that sbe point on the e3-board to that point mentioned on the board ..this board and my consoles board is same. is this a right way of using flash fun mode..? please see the pic iam unable to attach a pic here .so remove these (dot) n open the pic n tell me guz.. www(dot)mediafire(dot)com/view/?g6i553fb60kl80p

I think this will work,
if not, just solder the TRI Point to any other GND Point on your Mobe. it will do

[saqibmush]

Originally Posted by 3absiso I think this will work, if not, just solder the TRI Point to any other GND Point on your Mobe. it will do

i tried but agian error 10001100
in tf card start logging...
program PS3 BIOS.
fail to initialize PS3 BIOS.

[haz367]

Originally Posted by saqibmush i tried but agian error 10001100 in tf card start logging... program PS3 BIOS. fail to initialize PS3 BIOS.

that's one stuborn clip...right....reclip it..we know it's getting bored..but that will erase ur error and finally fix ur box

[Sasuke1981]

Originally Posted by daveyaz Hi...well i posted many threads asking for help...many nice guys helped me but another opinion will be very welcomed... Here is what happened and i think and hope that my ps3 is not bricked ... I got slim ps3..model : CECH-2504A Date code :1A... 160GB HDD.. I run the minverchk and it said 3.40 I made flash dump by E3 flasher..uploaded it and in the "check your dump" section in this forum, they said my dump is VALID...but said nothing about metldr.... i checked metldr on 0000820 and it was metldr1... when i used one key downgrade it started lighing up one by one and after 5-6 minutes the lights were flashing.... i pressed stop.... i wait 30 sec and try again... now my ps3 powers on for 2-3 sec and off again.... many guys helped me and said i need to connect wire between TRI and GND on the board.. i connected a wire (sticked it with tape no soldering).....power on but back off after 2-3 sec.... how to do this right ?? thanks for all...MJ999 + 3absiso and more....

How you suppose to get it work with no soldering but just use tape??? Wtf seriosly....use Your brain plz

[haz367]

i can't help...but whats wrong? if people really cannot solder or just start to shiver when almost toughing the "pad" and it needs fixing..then this "wire+sticky tape" really does work...so please do not say to use ur brain if u never tested this...it simply does work..used brain here...

ps: yeah i know.. no probs

[3absiso]

Originally Posted by haz367 i can't help...but whats wrong? if people really cannot solder or just start to shiver when almost toughing the "pad" and it needs fixing..then this "wire+sticky tape" really does work...so please do not say to use ur brain if u never tested this...it simply does work..used brain here... ps: yeah i know.. no probs

Remember the Guy i helped him on The PM since he does not speak English, i had to help him in Arabic.
did you know he soldered the TRI to SBE? Guess, ho took a knife and heated it up an put small solder on the points

[saqibmush]

Originally Posted by 3absiso I think this will work, if not, just solder the TRI Point to any other GND Point on your Mobe. it will do

where is that GND point on the board can u guyz refer me any pic from which i could find that easily..

[3absiso]

Originally Posted by saqibmush where is that GND point on the board can u guyz refer me any pic from which i could find that easily..

THE SBE point should work.
what is your mobo to send you diagram of the GRD Points