[3absiso]

Originally Posted by saqibmush i apllied the thermal paste..but i had only one plate installed under the board i hadn't installed any other plates ...heat sinker n the fans are also there intact without plates ...they are screwed from down side through the only plate installed under the board ..

I do not understand what you say.
how much time does it take to turn off???

[saqibmush]

Originally Posted by 3absiso I do not understand what you say. how much time does it take to turn off???

when i switch it on my conosle switches off within a minute..gives no display butt HDD light blinks n usb ports are working

[3absiso]

Originally Posted by saqibmush when i switch it on my conosle switches off within a minute..gives no display butt HDD light blinks n usb ports are working

did you check the Fan is rotating?

[haz367]

Originally Posted by saqibmush i got ste time and date screen xmb loads normally..

posted 2 hours ago...seems fixed ^^

Originally Posted by saqibmush what i have done let me explain.. 1- i put the patched dump in tf card an in flash fun it again..successfuully 2-Process complete than i used and downgrade dongle and put my console into FSM..successfully (after that step i uninstalled the e3 flasher n instaleed the hdd in console from the esata station..) 3- now i put files in Lv2diag.self n PS3UPDAT.PUP file in flash n booted my consolee. 4- switched on da console again and after some times it switched off again. 5- put da second step file Lv2diag.self in flash..n again switch on my console n it switched off again.. Now when i starts my console it after some times automaticaly switches off. USB is working HHD activity is also there..but console automaticalyy switches off after some time...

posted 2 hours ago..well let's say 2 hours and couple minutes

don't get it?! if it aint broke don't fix it..i guess it must be fixed again
let's hope 3absiso can help u... cuse xmb boots..then decide to "flash again"

just for the shizzle?
goodluck tho

[saqibmush]

Originally Posted by 3absiso did you check the Fan is rotating?

fan is working..i forgot one thing to mention man i used old versionsof Lv2diag.self n PS3UPDAT.PUP files almost 2 years old versions of these files using khalkedon tutorial..

may be that is creating the problem as these files were almost two years old n khalkedon method is also old..

[haz367]

keep ignoring..no probs...don't care really...but why oh why u flash again after fix = boot into xmb? u didn't say in any post that something happend! that's why i'm asking..it's an interesting Q not?

[3absiso]

Originally Posted by saqibmush fan is working..i forgot one thing to mention man i used old versionsof Lv2diag.self n PS3UPDAT.PUP files almost 2 years old versions of these files using khalkedon tutorial.. may be that is creating the problem as these files were almost two years old n khalkedon method is also old..

What Self Files did you use:
the first one should be around 366 KB (Get in FSM)
the second self should be around 202 KB (Get Out of FSM)

[katsuru]

Guys,

Got a problem with a CECHL , while installing 3.55 from recovery with toggle qa enabled, it turned itself off, and now does not start. Beeps 3 times and then red flashing light.

I guess my only way now is soldering ? but from where to where should I be soldering so it stays on ?

[saqibmush]

Originally Posted by 3absiso What Self Files did you use: the first one should be around 366 KB (Get in FSM) the second self should be around 202 KB (Get Out of FSM)

First self filee was of 228kb n second self file was of 202kb

[3absiso]

Originally Posted by katsuru Guys, Got a problem with a CECHL , while installing 3.55 from recovery with toggle qa enabled, it turned itself off, and now does not start. Beeps 3 times and then red flashing light. I guess my only way now is soldering ? but from where to where should I be soldering so it stays on ?

What is your Mobo?
and why did it turned off? over heating ? or what, did you make sure all the pads are on the place, and how much time did it take to shutt off?

You Can solder TRI on Mobo ro SBE to Clip Sebon and make the flasher in Fun Flash (100000)