[saqibmush]

Originally Posted by haz367 not me..hehe...i have a good day sir the english again ...let's keep it at "we have all our bad day..or for girls out there..time of the month ) but this was nothing..it's all good...u didn't mis anythin ok, cuse the guy @saqibmush looks to have a FSM mode problem on OFW 4.31 and PM'd me i like to put it here for clarity and...then he must have not "exited" before he fixed/restored with OFW 4.31 dump?!

still stuck guyz

what i have done let me explain
first flash the patched dump with first switch up n SBE n TRI State connected...but after that my console is giving no display..turns off automatically after few seconds..
************* [ - Post Merged - ] *************
flashed again with originale dump and now iam againin 4.31 FSM Mode

[playerkp420]

Originally Posted by saqibmush still stuck guyz what i have done let me explain first flash the patched dump with first switch up n SBE n TRI State connected...but after that my console is giving no display..turns off automatically after few seconds.. ************* [ - Post Merged - ] ************* flashed again with originale dump and now iam againin 4.31 FSM Mode

After you flashed the patched dump, did you have the USB stick in the right usb port, with the files name correctly, then turn on PS3?

[godking666]

kp is right. its gotta be the right usb port :P i bet thats the issue

[saqibmush]

what is the issue ???

[playerkp420]

Originally Posted by saqibmush what is the issue ???

You are already in FSM mode. So after you flash the patched dump and reboot the PS3, it will not show the "connect controller screen".
It is going to look for the Lvdiag.self so it knows what function to call.
When it doesn't find it, it will shut down. And look like it is bricked.

So put the usb drive in the right most usb port, after you flash the patched dump. Then reboot the ps3 and wait for it to install the firmware, etc....

[saqibmush]

Originally Posted by playerkp420 You are already in FSM mode. So after you flash the patched dump and reboot the PS3, it will not show the "connect controller screen". It is going to look for the Lvdiag.self so it knows what function to call. When it doesn't find it, it will shut down. And look like it is bricked. So put the usb drive in the right most usb port, after you flash the patched dump. Then reboot the ps3 and wait for it to install the firmware, etc....

k i got it thanx man...but let me tell for flashing the patched dump is there any need to have an connected wire from sbe to tristate or i should disconnect that connection....
n for flash fun i would have to 100000 for switches on e3 ....

am i right...

[playerkp420]

Originally Posted by saqibmush k i got it thanx man...but let me tell for flashing the patched dump is there any need to have an connected wire from sbe to tristate or i should disconnect that connection.... n for flash fun i would have to 100000 for switches on e3 .... am i right...

You are not bricked, so you don't need the wire. You can just leave it though. Just flash the patched dump with all switches down.

[noobzega]

Good to see people helping I'm back so I'll be here if someone need some help or advice.

[saqibmush]

Originally Posted by playerkp420 You are not bricked, so you don't need the wire. You can just leave it though. Just flash the patched dump with all switches down.

while flashing the patched dump with all switches down i got error..
start logging...
PS3 is operating Nor.
...?????

[playerkp420]

Originally Posted by saqibmush while flashing the patched dump with all switches down i got error.. start logging... PS3 is operating Nor. ...?????

Flash it with the 1st switch up then.