[xAfgkiller96x]

Originally Posted by Mr.Dutch use the solder iron again and melt the solder so you can remove it. are you sure you want to do this yourself?, you are so unexperienced.

Yes man , thanks i will do it im back in 10 min or 20 min THANKS
************* [ - Post Merged - ] *************
@playerkp420 @Mr.Dutch

like this , i am ready ?

now i have to install the flasher or without flasher ??

[Mr.Dutch]

Originally Posted by xAfgkiller96x now i have to install the flasher or without flasher ??

you could try to start the ps3 without the flasher to see if it stays on, if it shut down again you have a hardware error.

if it stays on you can install the flasher again.

about your wire, there's a bit too much copper exposed from the wire, but in this case it won't hurt.

EDIT: after a second thought the copper is exposed too much, make sure it dousnt short to any other point on the mainboard

[xAfgkiller96x]

Originally Posted by Mr.Dutch you could try to start the ps3 without the flasher to see if it stays on, if it shut down again you have a hardware error. if it stays on you can install the flasher again. about your wire, there's a bit too much copper exposed from the wire, but in this case it won't hurt. EDIT: after a second thought the copper is exposed too much, make sure it dousnt short to any other point on the mainboard

Can i start the ps3 now ?

yea i know i have saved from other points ..

[Mr.Dutch]

Originally Posted by xAfgkiller96x Can i start the ps3 now ?

if you have the fan connected, then i guess you can.

[xAfgkiller96x]

Originally Posted by Mr.Dutch if you have the fan connected, then i guess you can.

Ok the ps3 starts but im not getting any screen on the TV ?

EDIT :
And the USB ports still not work ..

[Mr.Dutch]

Originally Posted by xAfgkiller96x Ok the ps3 starts but im not getting any screen on the TV ?

this is suppose to happen, it halts the ps3 so you can flash again.

well at least it is not a hardware error.

do you have a good dump that you can flash back?

@xAfgkiller96x , it's best to wait until @playerkp420 or @baileyscream replies, i don't know that much about the e3 flasher, and if you flash back a bad dump you can throw your ps3 out the window.

[xAfgkiller96x]

Originally Posted by Mr.Dutch this is suppose to happen, it halts the ps3 so you can flash again. well at least it is not a hardware error. do you have a good dump that you can flash back?

Yes ,but want to make a new Dump .. is it possible ?
The ps3 dont shut off :D with the power button ...

[Mr.Dutch]

Originally Posted by xAfgkiller96x Yes ,but want to make a new Dump .. is it possible ?

aslong as the ps3 stays on you can make a new dump, but just don't flash anything before someone confirms it is safe to do.

[xAfgkiller96x]

Originally Posted by Mr.Dutch this is suppose to happen, it halts the ps3 so you can flash again. well at least it is not a hardware error. do you have a good dump that you can flash back? @xAfgkiller96x , it's best to wait until @playerkp420 or @baileyscream replies, i don't know that much about the e3 flasher, and if you flash back a bad dump you can throw your ps3 out the window.

i have a good dump i checked it with flowrebuilder and NORinspector and NOR PATCHER three musketeers ...
and all three said its good dump

EDIT: HOW TURN THE PS3 OFF ? dont work with powerbutton ..

[Mr.Dutch]

Originally Posted by xAfgkiller96x i have a good dump i checked it with flowrebuilder and NORinspector and NOR PATCHER three musketeers ... and all three said its good dump

is this a 100% quarantee? , the problem is if it's not correct and you flash it, you make things more worse.

and what if you have the clip not seated correctly now...

EDIT: if you hold the power button long enough, will it shutdown?