[xAfgkiller96x]

Originally Posted by baileyscream yes if you patched it then it will say 3.55 check the one from yesterday if the statistics is out then patch it and check it again and it should be correct.

i checked it yesterday ..
Was ok but Just

The fine blue bars at either side are what need checking (the one to the left is highlighted in red put your mouse on the left line and you should get a reading between 18.38% - 29.01% (in the area circled in blue)

and mine 4.30.000 (Yesterday) was 18,24%

[baileyscream]

Originally Posted by xAfgkiller96x i checked it yesterday .. Was ok but Just The fine blue bars at either side are what need checking (the one to the left is highlighted in red put your mouse on the left line and you should get a reading between 18.38% - 29.01% (in the area circled in blue) and mine 4.30.000 (Yesterday) was 18,24%

yes thats better but patch your dump then check it again and it should show correct value's

use rogero auto patcher
http://www.mediafire.com/?kd22h28nr7ccrjc#!

[xAfgkiller96x]

Originally Posted by baileyscream yes thats better but patch your dump then check it again and it should show correct value's use rogero auto patcher http://www.mediafire.com/?kd22h28nr7ccrjc#!

ok first patch the dump and than check it and than install it ?..
and than ?

EDIT : ok Patched
EDIT 2: Should i patch The (MY) bkpps3.bin or bkpps3.bin (my flowrebuilder "extract and byte reserve")

Can u please check it ? ..
im really not sure what im doing ..

The patched from yesterday (ros0:430.000)

[baileyscream]

Originally Posted by xAfgkiller96x ok first patch the dump and than check it and than install it ?.. and than ? EDIT : ok Patched Can u please check it ? .. im really not sure what im doing .. The patched from yesterday (ros0:430.000)

that needs byte reversing
its all in the guide

[xAfgkiller96x]

Originally Posted by baileyscream that needs byte reversing its all in the guide

SHOULD I PATCH MY ORIGINAL BKPPS3.BIN ? (MY)
OR PATCH THE BKPPS3.BIN.SWAP ? (FLOWREBUILDER EXTRACT AND BYTE RESERVE?) ??????? @baileyscream @playerkp420

OK ITS INSTALLING THE PATCHED Backup ..

other way found ..

Ok if its finished , and than i will remove the wire , will the ps3 start normally ? and i can enterFactory service mode ? and will the usb cable work ?

[baileyscream]

Originally Posted by xAfgkiller96x SHOULD I PATCH MY ORIGINAL BKPPS3.BIN ? (MY) OR PATCH THE BKPPS3.BIN.SWAP ? (FLOWREBUILDER EXTRACT AND BYTE RESERVE?) ??????? @baileyscream @playerkp420 Do i need to put the e3_downgrader.bin in the SD card too ?

patch the origional and it will give you a second dump that is patched.
byte reverse and extract it in flowrebuilder
then check it in hxd

if its good then it can be sent to the dump check thread.

[xAfgkiller96x]

Originally Posted by baileyscream patch the origional and it will give you a second dump that is patched. byte reverse and extract it in flowrebuilder then check it in hxd if its good then it can be sent to the dump check thread.

i first swaped the bkpps3 .. and than patched it ,

btw.. the dump is installing ..

[baileyscream]

Originally Posted by xAfgkiller96x i first swaped the bkpps3 .. and than patched it , btw.. the dump is installing ..

installing?? you mean the patch is installing?

ok once done check it.

its nearly midnight for me so i will pick this up tomorrow.

check that patched dump

but dont flash it back tonight.

dont rush this take your time. last thing you want is to make things worse.

[xAfgkiller96x]

Originally Posted by baileyscream installing?? you mean the patch is installing? ok once done check it. its nearly midnight for me so i will pick this up tomorrow. check that patched dump but dont flash it back tonight. dont rush this take your time. last thing you want is to make things worse.

the patched backup is flashing back , and its done ..
i have to remove the wire from Tristate to GND ? @Mr.Dutch

[KOOLGUS]

you have glod and fried motherboard