[olert]

@MJ999

Originally Posted by MJ999 Still, trvk_prog1 is invalid Tip : Re-seat the clip, clean the clip and chip with alcohol and re-dump

I have tried that, with no luck :-(

I will try with a new clip.......

[3absiso]

Originally Posted by olert @MJ999 I have tried that, with no luck :-( I will try with a new clip.......

Try to update the OFW 4.31 from recovery and dump again

[olert]

Originally Posted by 3absiso Try to update the OFW 4.31 from recovery and dump again

I've tried that to :-(

Will it have any impact to reset the ps3 to factory mode ?

[3absiso]

Originally Posted by olert I've tried that to :-( Will it have any impact to reset the ps3 to factory mode ?

TRy it again
and do not proceed until you have a valid dump

[Zaplutus]

have send in nand dump checked it and all i got some low % on the statistics but havent patched it.
everything else seems fine

[BlacKaos]

So I checked my dump with baileys guide and i have a question. Does everything need to match up as I had a 0h value of 18.23%, my dump did not match the first image after checking for malformed headings with some of the 00000800 offset values till the 000008F0 being different. That and my 00FC0000 did not match. Does this immediately rule it as bad? Would anything change if I said mine is NTSC CECHH?

[stepheng67]

I just sent a dump file to be checked. OWF is 3.25 and used combination Bailys Tutorial, Tutorial from PS3 dev wiki and nor inspector.

TIA

[unitedrule]

I've just sent my dump, its 3.60 ofw
I'm following Baily's Tutorial

[3absiso]

Originally Posted by stepheng67 I just sent a dump file to be checked. OWF is 3.25 and used combination Bailys Tutorial, Tutorial from PS3 dev wiki and nor inspector. TIA

YOUR DUMP IS VALID

ROS0/ROS1 is 4.25/4.21: Valid

tvrk_prog0 : 3.55/3.55_DEX Valid

tvrk_prog1 : 3.50 Valid

PS3 Model: CECH-20xx

Mobo: DYN-001

HD: TOSHIBA MK1255GSX
************* [ - Post Merged - ] *************

Originally Posted by Zaplutus have send in nand dump checked it and all i got some low % on the statistics but havent patched it. everything else seems fine

I could not download the Dump
************* [ - Post Merged - ] *************

Originally Posted by unitedrule I've just sent my dump

YOUR DUMP IS VALID

ROS0/ROS1 is 4.11/3.60: Valid

tvrk_prog0 : 3.50 Valid

tvrk_prog1 : 3.55/3.55_DEX Valid

PS3 Model: CECH-20xx

Mobo: DYN-001

HD: TOSHIBA MK2555GSX
************* [ - Post Merged - ] *************

Originally Posted by BlacKaos So I checked my dump with baileys guide and i have a question. Does everything need to match up as I had a 0h value of 18.23%, my dump did not match the first image after checking for malformed headings with some of the 00000800 offset values till the 000008F0 being different. That and my 00FC0000 did not match. Does this immediately rule it as bad? Would anything change if I said mine is NTSC CECHH?

I could not find your Dump

[stepheng67]

I am a little confused at this point depending on who's guide I use. I've been successful with phats following Bailys Tutorial, so if I follow Nailys, I do not have to patch the bin if I use the "one-key downgrade", correct?

Only if it fails I do. then my second questions is can you point be to a decent guide for patching.

I just do not want to brick this one.

Thanks.