[MRDOCA]

You're awesome man thanks heaps

Swyped on my SGS3

[CyKoDeLiC]

Ok, thx for the answer. My second question at the and was meant a little different.

When I am on this 4.31CFW, is it possible to then go to Rogero or Rebug CFW 4.30 via XMB or Recovery Menü? Or do I have to downgrade to 3.55, which isn't possible at this console?

My console is now in the state, where I flashed the patched.bin with the musketeers patches in it. It now asks me for a firmware 4.31 or higher in the recovery mode. So just install this CFW and it shoud work?

[DEFAULTDNB]

Originally Posted by CyKoDeLiC Ok, thx for the answer. My second question at the and was meant a little different. When I am on this 4.31CFW, is it possible to then go to Rogero or Rebug CFW 4.30 via XMB or Recovery Menü? Or do I have to downgrade to 3.55, which isn't possible at this console? My console is now in the state, where I flashed the patched.bin with the musketeers patches in it. It now asks me for a firmware 4.31 or higher in the recovery mode. So just install this CFW and it shoud work?

Ideally you would await confirmation from a member with better knowledge of flashers and this exact process.

But...when you are on 4.31 CFW yes you should be able to downgrade using the ROGERO downgrader pup.

[CyKoDeLiC]

Originally Posted by DEFAULTDNB Ideally you would await confirmation from a member with better knowledge of flashers and this exact process. But...when you are on 4.31 CFW yes you should be able to downgrade using the ROGERO downgrader pup.

Ok, I took one for the team and it worked like a charm. I am now on 4.31 Mirala. What to do now to get to 4.30 Rogero? I can't go to 3.55 via Rogero Downgrader 4.25to3.55.pup, cause minimum is 3.56.

Maybe installing Rebug999 and then go to Rebug 4.30.1 is the right way?

[DEFAULTDNB]

Hmm, there is a thread here that may help you: http://www.ps3hax.net/showthread.php?t=51600

I am entirely unsure how you can downgrade to 4.30 CFW from 4.31 CFW with a min OFW of 3.56... I dont think downgrader pup will work for you: rogero is based on 3.55

After the Downgrader PUP installs you'll be on a hybrid CFW3.55 that will still shows the spoofed ver4.21 from system settings.

I cant find much out about REBUG 999 downgrader.. other than you need to QA flag and dehash after use, so that doesnt seem to be an option.

I think I remember @toolz downgrading from 4.31 CFW back to Rogero 4.30 2.05....

EDIT: http://www.ps3hax.net/showpost.php?p...&postcount=128

@toolz how did you achieve this?

[CyKoDeLiC]

Ok, I've send him PM.

Wasn't there a point in Rebug Toolbox to reset and toggle qa?

[DEFAULTDNB]

Originally Posted by CyKoDeLiC Ok, I've send him PM. Wasn't there a point in Rebug Toolbox to reset and toggle qa?

Toggle QA was for 3.55 based FW, not 4.xx based.... although miralatijera does claim to allow QA enable/disable, I dont think it is possible to set the initial toggle (generate token) from above 3.55 cfw.

[CyKoDeLiC]

Ok, nevermind. This CFW is acutally quiet good. Plays Crysis 3 and runs showtime media player. Thanks to the dev!

[playerkp420]

Originally Posted by DEFAULTDNB Hmm, there is a thread here that may help you: http://www.ps3hax.net/showthread.php?t=51600 I am entirely unsure how you can downgrade to 4.30 CFW from 4.31 CFW with a min OFW of 3.56... I dont think downgrader pup will work for you: rogero is based on 3.55 I cant find much out about REBUG 999 downgrader.. other than you need to QA flag and dehash after use, so that doesnt seem to be an option. I think I remember @toolz downgrading from 4.31 CFW back to Rogero 4.30 2.05.... EDIT: http://www.ps3hax.net/showpost.php?p...&postcount=128 @toolz how did you achieve this?

I wish I had a min. praxis 3.56 PS3 to test with. I too wonder if one of the downgrader PUPs will work. It might because the PUPs syscon is changed to 4.40 or 9.99.
I would like to know if you could install it, then update to a different 4.xx CFW.

[KBracing6]

Just wanted to make sure before I go messing with anything. I'm currently on OFW 3.40 all I have to do it just start of on step one correct? Or should i update to OFW 3.55 then start of on step 1?