[Mr.Dutch]

Originally Posted by xAfgkiller96x I have a question: Can i Solder the Usb Ports directly to the mainboard ? Or the Ps3 controller? FAT MODEL : CECH-K03 Motherboard : DIA-002

make a good high res picture of the board with the usb ports, both sides if possible and post it here.

[baileyscream]

use this as a last no going back attempt.
if this doesnt work then you will be stuck in fsm

-----------------------------------------------------------------------------

re-flash the nor / nand with the origional dump

you should be back on ofw

see if your usb's work.

if they do then ENTER FSM

re-flash your patched dump

you should now have your patched firmware and be in fsm

put the fsm files on a usb stick and see if it will now downgrade (fsm should allow the usb ports to work)

[xAfgkiller96x]

Originally Posted by baileyscream use this as a last no going back attempt. if this doesnt work then you will be stuck in fsm ----------------------------------------------------------------------------- re-flash the nor / nand with the origional dump you should be back on ofw see if your usb's work. if they do then ENTER FSM re-flash your patched dump you should now have your patched firmware and be in fsm put the fsm files on a usb stick and see if it will now downgrade (fsm should allow the usb ports to work)

I just found my Dump.swap 4.30 and install it and still dont work ..

i think maybe the wlan board is damaged (where the flexcable comes)
or something in on the mainboard ..

ps.: @Mr.Dutch i will upload the picture in 5 minutes..

[baileyscream]

Originally Posted by xAfgkiller96x I just found my Dump.swap 4.30 and install it and still dont work .. i think maybe the wlan board is damaged (where the flexcable comes) or something in on the mainboard .. ps.: @Mr.Dutch i will upload the picture in 5 minutes..

do you have any game disck with 4.30 ofw update on it?
you could try re-installing it via disc and see if it solves it.

probably wont but atleast you would have tried everything software wise first.

[Mr.Dutch]

Originally Posted by xAfgkiller96x ps.: @Mr.Dutch i will upload the picture in 5 minutes..

your post was 11 hours ago, where's that pic.

[xAfgkiller96x]

Originally Posted by baileyscream do you have any game disck with 4.30 ofw update on it? you could try re-installing it via disc and see if it solves it. probably wont but atleast you would have tried everything software wise first.

-Dont have cd with ofw 430 just black ops . :D

i dont know if you know what i mean..
-I Found my original dump BUT just the swap ..
than i install the swap and the usb ports still not work.
-I am actually on the "connect Controller" screen.
______________________________

@Mr.Dutch , here are 13 pictures of the mainboard and the usb board ..
i hope you can help me ..
maybe i can solder the player directly to the mainboard ?:D just to install 3.55 and get out of the controller screen..
http://www.mediafire.com/?d133dtmyd30t89d

[Mr.Dutch]

Originally Posted by xAfgkiller96x here are 13 pictures of the mainboard and the usb board ..

the pics that are important (from the bluetooth board) are way from being sharp.

i added 4 points to measure, you should at least read 5V at the 3 points near the black 8 legs ic.

if the 2 points 5V to usb fail, then you can rewire them, if all 4 points fail, you need to get 5V from the mainboard.



EDIT: @xAfgkiller96x , i added another picture from the other side, this picture is much better.
if you don't have the 3,3V on the points i marked then bypassing the usb with 5V is not enough.

EDIT2: the two points near the 6 legs black ic can read 5V instead of 3,3V.

usb controller chip

[xAfgkiller96x]

Originally Posted by Mr.Dutch the pics that are important (from the bluetooth board) are way from being sharp. i added 4 points to measure, you should at least read 5V at the 3 points near the black 8 legs ic. if the 2 points 5V to usb fail, then you can rewire them, if all 4 points fail, you need to get 5V from the mainboard. EDIT: @xAfgkiller96x , i added another picture from the other side, this picture is much better. if you don't have the 3,3V on the points i marked then bypassing the usb with 5V is not enough. EDIT2: the two points near the 6 legs black ic can read 5V instead of 3,3V. usb controller chip

First of all , thx for ur help and i really tray to understan you..
But what is 5v or 3, 3v ?
Should i take other pics from the boards?
Can you show just what i need to solder ?
)

[Mr.Dutch]

Originally Posted by xAfgkiller96x Can you show just what i need to solder ? )

don't you have a multimeter at all?

it's pretty pointless to just solder anything without knowing what's going on.

[baileyscream]

Originally Posted by xAfgkiller96x -Dont have cd with ofw 430 just black ops . :D i dont know if you know what i mean.. -I Found my original dump BUT just the swap .. than i install the swap and the usb ports still not work. -I am actually on the "connect Controller" screen.

yes i know what you mean

but buy a multimeter and follow Mr.fuse now

http://technikalworld.blogspot.co.uk...ne-repair.html