[Sarah1331]

Originally Posted by haz367 lol..what a waste for NORS, thx for confirm, baileyscream told me the reading ONLY is 50/50 for NOR, guess the DIA-001 is the negative side can u confirm one more thing since the DIA-001 isn't working even with correct wired/setup for NOR-Progskeet 1.2/Reading flash the error with Winskeet = Device not found, it's Spansion, tested both in settings = Device not found alrighty..good practice then afterall hey @Sarah1331 , can u also confirm if i woud gice my skeet 1.0 a try without using ATX PSU and proper soldered it would work to dump/write nor..even if the board is dead..ignore it..for testing u see.. keep it up guys and girls? (they tend to be good at soldering to..) this requires atleast 3 joints no drugs guys its not good for u thx again

If you remove the nor you can read and write using progskeet 1.0 yes (wire 3.3 to nor chip)

as for it in circuit you need external power (don't wire 3.3 to mobo from skeet)

[haz367]

Originally Posted by Sarah1331 Sorry I am jumping in half way Dia-001 is a nor model and your progskeet 1.2 won't work Ignore all the r7/r8 leave them both bridged and don't connect any 3.3v wire to skeet from mobo if your using external or ps3 to power Only wire 3.3 to ps3 if your using no external power

no problem, thx for wasting some time

R7 is removed and bridged
R8 = removed and open must be bridged for NOR/external ATX?

u say..both closed for NOR/external ATX power correct, and yes i have NO 3.3v wire from/to Progskeet 1.2 only 2 GND wires from skeet to mb and 3.3v/gnd from atx to mb should it detect device and try dump? even tho its not supported?

thx again..me noob keeps trying


edit:
ok so for skeet 1.0 and onboard flashing it requires external ATX power like i'm doing atm..right? before wasting more...it would be great info to know if the skeet 1.2 is atleast capable in dumping the DIA-001 NOR? before messing with Progskeet 1.0...what a stuff haha

[Sarah1331]

Originally Posted by haz367 no problem, thx for wasting some time R7 is removed and bridged R8 = removed and open must be bridged for NOR/external ATX u say..both closed for NOR/external ATX power correct, and yes i have NO 3.3v wire from/to Progskeet 1.2 only 2 GND wires from skeet to mb and 3.3v/gnd from atx to mb should it detect device nd try dump thx again..noob keeps trying

Ok here goes
I always have solder blob connecting r8 and r7

If I use ps3 to power mobo or external atx I do not connect 3.3 from skeet to mobo

If I do a NAND console I connect 3.3 to mobo and never use ps3 to power or atx

The only console you should wire 3.3 to mobo from skeet is a NAND console and never use any other power supply

Does this help

[haz367]

right..right..then it must be me or there's some resistor confusion..right? just asking as atm i have only R7 solder blobbed/bridged/closed and R8 open for NOR, then one more try i guess with Progskeet 1.2 and both R7/R8 solder blobbed/closed/bridged

cheers guys..

[4DoorITR]

I'll say this again ... if your using a Progskeet 1.2 for NOR then R7 must be open and R8 must be closed. So far I have been able to read from 2 different boards but of course no writing.

[Sarah1331]

Originally Posted by 4DoorITR I'll say this again ... if your using a Progskeet 1.2 for NOR then R7 must be open and R8 must be closed. So far I have been able to read from 2 different boards but of course no writing.

So no difference to what I said
just dont wire 3.3v from skeet to mobo

[haz367]

i must misread like some misread ifi..fii

atm r7 closed/r8 open, done for today, nxt day gonna measure the 3.3 line what it gives on the board and fix r7/r8..my hands to tired now

this aint no walk in the park..stil cool to try and thx again..virtual free beers from me and else they rot..a free steak aswel..

[Sarah1331]

Originally Posted by haz367 i must misread like some misread ifi..fii atm r7 closed/r8 open, done for today, nxt day gonna measure the 3.3 line what it gives on the board and fix r7/r8..my hands to tired now this aint no walk in the park..stil cool to try and thx again..virtual free beers from me and else they rot..a free steak aswel..

Close r8 and r7
Don't wire 3.3 to mobo

[haz367]

haha.. is it me weed..or what? nice tho..so i can leave my shiny r7 solderblob untoughed

ok, wil do nxt day..solderblob r8, and like in this stage, only gnd from skeet 1.2 > mb, nor feeded by atx psu..

[4DoorITR]

Originally Posted by Sarah1331 Close r8 and r7 Don't wire 3.3 to mobo

Isn't he using a 1.2? If he is dumping a NOR he needs to have R7 open. Why do you say closed?

Also if your getting "device not found" in Winskeet make sure your using the WinUSB driver for the Progskeet. That is the error you will get when using the libusb driver.