|
|
08-19-2011
|
#1 |
  
Join Date: Feb 2007
Posts: 6,988
Likes: 371
Liked 8,045 Times in 1,247 Posts
Mentioned: 585 Post(s)
Tagged: 0 Thread(s)
|
Noob Tutorial: How to downgrade/flash your PS3 from firmware 3.70 to 3.55 via ProgSkeet/Teensy++ and install 3.55 Kmeaw CFW
Most of you have heard the ... [READ MORE]
|
|
|
|
Likes: (8) |
|
08-19-2011
|
#2 |
  Join Date: May 2008
Location: The World Wide Web
Posts: 40
Likes: 11
Liked 75 Times in 25 Posts
Mentioned: 56 Post(s)
Tagged: 0 Thread(s)
|
Not bad only one mistake, the picture of "Samsung Memory" is wrong.
You got RAM showing, not the flash, this is the right picture: http://www.ps3crunch.net/forum/images/news/samsung.jpg And to support Samsung you need the latest Progskeet flasher: 110819 All versions before that will not dump/flash Samsung memory. With the latest Progskeet flasher, it has "ByteSwap" feature, that should remove the need for FlowRebuilder to swap the bytes around, but I can't personally confirm it, as I have not tested the new feature. Last edited by garyopa; 08-19-2011 at 05:36 PM. |
|
|
|
|
Likes: (3) |
|
08-19-2011
|
#3 | |
|
Join Date: Feb 2007
Posts: 6,988
Likes: 371
Liked 8,045 Times in 1,247 Posts
Mentioned: 585 Post(s)
Tagged: 0 Thread(s)
|
|
|
|
|
|
|
08-19-2011
|
#4 |
|
Senior Member
 
Join Date: May 2011
Location: somewhere close
Posts: 3,983
Likes: 1,188
Liked 2,218 Times in 927 Posts
Mentioned: 331 Post(s)
Tagged: 0 Thread(s)
|
link is not woking for me.
|
|
|
|
|
08-19-2011
|
#5 |
|
Member
Join Date: Feb 2011
Posts: 42
Likes: 4
Liked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
this is very helpful. one question though, when the solderless comes out, is it clip onto NOR and done. instead of pin soldering?
|
|
|
|
|
08-19-2011
|
#6 | |
|
Member
 Join Date: Jul 2011
Posts: 96
Likes: 4
Liked 27 Times in 21 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
__________________
|
|
|
|
|
|
08-19-2011
|
#7 |
|
Apprentice
Join Date: Jan 2011
Posts: 25
Likes: 0
Liked 1 Time in 1 Post
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Good stuff!! Any set time on when the solderless version will be released?
|
|
|
|
|
08-19-2011
|
#8 | |
|
Member
Join Date: Jul 2011
Posts: 96
Likes: 4
Liked 27 Times in 21 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
__________________
|
|
|
|
|
|
08-19-2011
|
#9 |
|
Member
 
Join Date: Jan 2011
Posts: 168
Likes: 13
Liked 29 Times in 25 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
im not a noob but, noob in soldering so.. this isn't for me.
i can could do most step except step 3... i would wait for solderless and this guide would be perfect!! noob proof :D 
|
|
|
|
|
08-19-2011
|
#10 |
|
Apprentice
Join Date: Jan 2011
Posts: 25
Likes: 0
Liked 1 Time in 1 Post
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Yeahh just watch it be super expensive when it comes out though :\
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
|
|
