[enomax00]

hello I present my problem.
I have a ps3 slim 2511A factory with 3.56 OFW, I installed my E3 intermittent successfully achieve backup of my bios, then use the tutorial TDCroPower2 to lower my second ps3 slim, patch everything and then try to raise the bkpps3.bin, the complete the process of the eight lights turn off the ps3 and unplug the power, and then try to start to see the message Press the PS button and not lit, just three seconds and then power off. Achieve restore the bios from Flash Fun mode. The PS3 went back to work I went back to try everything. But the same result. Now restored it back copies of the bios turned on the ps3. Then cut the power and try to turn it on again and I have brick, will not let me do or flash fun, or unlock. Someone help me.
Sorry for my bad English.

[carldenning]

Originally Posted by enomax00 hello I present my problem. I have a ps3 slim 2511A factory with 3.56 OFW, I installed my E3 intermittent successfully achieve backup of my bios, then use the tutorial TDCroPower2 to lower my second ps3 slim, patch everything and then try to raise the bkpps3.bin, the complete the process of the eight lights turn off the ps3 and unplug the power, and then try to start to see the message Press the PS button and not lit, just three seconds and then power off. Achieve restore the bios from Flash Fun mode. The PS3 went back to work I went back to try everything. But the same result. Now restored it back copies of the bios turned on the ps3. Then cut the power and try to turn it on again and I have brick, will not let me do or flash fun, or unlock. Someone help me. Sorry for my bad English.

u do know u cant downgrade to 3.55 if the ps3 factory fw is 3.56 !!

[enomax00]

but I can do to make it work again even in 3.56. or 4.10. this brick

[carldenning]

Originally Posted by enomax00 but I can do to make it work again even in 3.56. or 4.10. this brick

if u got a good back up then im sure u can get back 4.10 . there is a 3.56 cfw called JFW DH PS3 3.56 which u could downgrade to but only if its possible with e3 , i know from proskeet u can , maybe email e3 to see if u can go to JFW DH PS3 3.56 or ask some one here

[pereb27]

While on 3.56 OFW, use MinVerChk PUP (in the XMB) to check minimum firmware.

[enomax00]

I have bad news, I just realized that my E3 no light flashing not have reviewed all, I have disassembled and assembled 4 times, and there is no failure, I can not charge the backup of my bios if not light, may have burned ¿?

[jhax78]

Originally Posted by enomax00 I have bad news, I just realized that my E3 no light flashing not have reviewed all, I have disassembled and assembled 4 times, and there is no failure, I can not charge the backup of my bios if not light, may have burned ¿?

check if the clip pins are straight

and the only way to unbrick is soldering the sbe to tristate
and flash 4.10 backup back to the nor
if you flash it back and it still rlod then the backup was bad (like 90% of e3 **** is bad)

upload the dump to mediafire for a look and post the link here

[enomax00]

The welding was carried out before the whole process, the backup I have it up and leave the link. and the problem is that I have already tried it on a second ps3 and not light that may have failed. I certainly this backup and restore a once a bick.

thank you very much for your help.


http://www.mediafire.com/?1r7f8vdq31am0dw

[racer0018]

If you still need help when I get home I will take a look at the dump and tell you if it is good or not. I will be home in like 10 hours. Thanks

[jhax78]

Originally Posted by enomax00 The welding was carried out before the whole process, the backup I have it up and leave the link. and the problem is that I have already tried it on a second ps3 and not light that may have failed. I certainly this backup and restore a once a bick. thank you very much for your help. http://www.mediafire.com/?1r7f8vdq31am0dw

the backup is just fine
get a real flasher like progskeet and flash the backup back
and throw that E3 junk in the bin where it belongs