[alirza]

Hello
I want to do the work (downgrading ) for (nand) and (noor) with work tools can be found at the full but I want to do the operation by the USB .. Is it possible that you give me a picture in a way that tie the pieces together.

my progskeet v1.2 With all accessories

[baileyscream]

Originally Posted by kokner I made a 3.55 dump,after manual validate i verified it with anaria's norvalidator and for cvtrm i have this error :cvtrm SCEI magicnbr :read 00000000! mismatch pattern '53434549'. In the picture of the tutorial for cvtrm the line u highlighted in blue is the same line i have 00 00 00 00 FF FF FF FF FF FF FF FF FF FF FF FF. I upgraded and remade a 4.30 dump and the line is 53 43 45 49 FF FF FF FF FF FF FF FF FF FF FF FF and no error from the norvalidator. Both lines are ok? from norvalidator is missing a pattern?

the nor validator is not finnished yet.

you need to go into his thread and quote him telling him your findings.

he may want to see your dumps so be prepaired to send them to him.

just use the validator to see if you can find an error with the tool (dont miss out manual validation) then report in his thread

he wants it fully tested and all problems reporting
************* [ - Post Merged - ] *************

Originally Posted by alirza Hello I want to do the work (downgrading ) for (nand) and (noor) with work tools can be found at the full but I want to do the operation by the USB .. Is it possible that you give me a picture in a way that tie the pieces together. my progskeet v1.2 With all accessories

progskeet 1.2 is not fully working yet.

and you cannot do it all via a usb anyway

[daveyaz]

Originally Posted by baileyscream solder sbe on the ps3 to sbe on the E3 ffc cable (found half way along the flex of the clip) find your board in the soldering section of the guide under "setting up E3" to see where the sbe point is then do the patch part of the guide again with "flash fun" switch up. switches 2 3 4 5 down 6 up it should take 10-15 minimum to flash. once done turn off ps3 put "flash fun" down and see if ps3 turns on

Dear i got my ps3 power up halt after wiring...

Now PLEASE could you be more specific how to proceed with the downgrading or debricking......one by one please because im not so expert...

PLEASE.............

[andybarrn]

working with E3 NOR Flasher, try to set up for dual boot, after downgrading from 4.31 ofw to 3.55 ofw, changed to 3.55 kmeaw, then updated e3 flasher, then as per your instructions tried to install cfw to e3 nor, flipped the switches like you said and started, upon completion looked at event log and instead of "OK. Backup E3 BIOS OK." it says "OK.
Program Nor OK." and now my ps3 only comes up to a black screen, any suggestions?

working with CECH-2501A

[haz367]

nvm....................ps3devwiki+e3 bg fix

[andybarrn]

thank you haz367, got back to the 3.55 cfw at least, still uncertain what to do differently from the tutorial in order to not program my nor with the wrong bios again, i guess i'll just check around and compare info from several sites, unless someone can point me in the right direction.

[haz367]

nvm.............

[fudd69]

hi everyone. just a question: i have progskeet v1.2 , can i use it without the slave board but using at its place the jtag programmer? thanks

[SandyRavage]

Bailey... CECH200A - DYN-001 E3 Flasher (NOR CLIP) I've followed your tut exactly and i was successful in downgrading my PS3, thank you!. However i am unsuccessful in preforming the "fast dual boot." There is no mention of severing the A&B connection in your tut. Also you don't mention if we need to solder point A to the SBCE on the E3 Flasher or Tri-state to SBE. Should this be done?

[baileyscream]

Originally Posted by SandyRavage Bailey... CECH200A - DYN-001 E3 Flasher (NOR CLIP) I've followed your tut exactly and i was successful in downgrading my PS3, thank you!. However i am unsuccessful in preforming the "fast dual boot." There is no mention of severing the A&B connection in your tut. Also you don't mention if we need to solder point A to the SBCE on the E3 Flasher or Tri-state to SBE. Should this be done?

start of the e3 guide
setting up e3
soldering
the teat point / soldering images show where to cut and to solder the linker.
the clip shouldnt really be used for dual boot as it comes loose to easly