[rot]

Trying to dump the nor on dia001.

I have r7 open, r8,r9,11 bridged.

Turn on the ps3 wait 10 secs plug in usb and i get usb not recognized or it will halting on 0x0

[v8s10]

Open r8, don't need r7 and r8 closed at the same time.

[stdule]

r8 open (you need a switch,r8 only bridge to the PC to recognize the driver for the installation progskeet), R9-R11 bridge, power ps3 wait 20 seconds r7 bridge (you need a switch) simultaneously connected the USB to the PC, then dump flash 3x verified by HXD program is a good flash without errors-VERY IMPORTANT!!LINK:http://www.ps3devwiki.com/wiki/Hardware_flashing

[rot]

Originally Posted by stdule r8 open (you need a switch,r8 only bridge to the PC to recognize the driver for the installation progskeet), R9-R11 bridge, power ps3 wait 20 seconds r7 bridge (you need a switch) simultaneously connected the USB to the PC, then dump flash 3x verified by HXD program is a good flash without errors-VERY IMPORTANT!!LINK:http://www.ps3devwiki.com/wiki/Hardware_flashing

according to wiki i need r8 closed. Tried it anyways get a device not found

[stdule]

But if you soldered a 2 wire to the progskeet(3.3v and gnd)on ps3 motherboard you must not R7 and R8 Bridge, r7 soldered you have to switch to open and closed(power on progskeet)first install the driver

[rot]

Originally Posted by stdule But if you soldered a 2 wire to the progskeet(3.3v and gnd)on ps3 motherboard you must not R7 and R8 Bridge, r7 soldered you have to switch to open and closed(power on progskeet)first install the driver

except i dont need a wire soldered there because i have r8 closed.

[baileyscream]

can you ppl give correct advice?
device not recognised:
1. you havent installed the drivers CLICK HERE FOR PROGSKEET DRIVERS
2 you need to use win xp 32bit (try to stay away from win 7 & 64 bit. if your on a microsoft OS)

R7 open
R8 closed
R9 & R11 (3.3v) bridged
turn on ps3 wait 3 to 5 sec than plug progskeet's usb into pc to halt the boot up & the pc should beep to say the progskeet has been recognised

if you power the NOR from the progskeet you need 3.3v feed from the progskeet and R7 & R8 closed (do not power the ps3 via the mains with these both closed) and this way is used to dump NOR when you have a soft brick only now.

you need anymore help go here :-
http://www.ps3hax.net/showthread.php?t=39766
i am still developing the thread but the progskeet NOR side is done.

[rot]

Originally Posted by baileyscream can you ppl give correct advice? device not recognised: 1. you havent installed the drivers CLICK HERE FOR PROGSKEET DRIVERS 2 you need to use win xp 32bit (try to stay away from win 7 & 64 bit. if your on a microsoft OS) R7 open R8 closed R9 & R11 (3.3v) bridged turn on ps3 wait 3 to 5 sec than plug progskeet's usb into pc to halt the boot up & the pc should beep to say the progskeet has been recognised if you power the NOR from the progskeet you need 3.3v feed from the progskeet and R7 & R8 closed (do not power the ps3 via the mains with these both closed) and this way is used to dump NOR when you have a soft brick only now. you need anymore help go here :- http://www.ps3hax.net/showthread.php?t=39766 i am still developing the thread but the progskeet NOR side is done.

yes i do have the drivers installed. It will either halt on 0x0 or it will give me an unknown usb device then device has malfunctioned when i plug in my usb

[baileyscream]

Originally Posted by rot yes i do have the drivers installed. It will either halt on 0x0 or it will give me an unknown usb device then device has malfunctioned when i plug in my usb

ok the halting at 0x0 fault i had the first time i did a dump on my first ps3.
i soldered all the wires from skeet to ps3 (i dont know if you have done the same)
and found i had "dead soldered" some wires by using a soldering iron that was to hot.
if you have soldered i would suggest re-soldering all the wires and take your time.

if you have used the NOR clip have you removed pin 46 as discussed in the wikki?
see here&here