[urbananonymous]

ok so short and sweet, i was getting ready to do a downgrade on a cech-h01 and i started taking it apart and then thought to myself that i should check to see what fw the system was on cause sometimes people bring me systems on 3.55 and below for downgrades not even knowing they dont need it. so i put the psu back on and turned it on and needed to connect a controller but i haddent reconnected the ribbon cable back to the mnother board for the usb ports... so since im such a lazy **** i tryed to connect it while the system was still on and as soon as i connectedf it it yloded... im thinking its a fuse... but where is the fuse on the cech-h01 mobo? if it is a fuse...

[playerkp420]

You should be turning them on, checking firmware, and making sure they work.

At least I do, before everyone I do. Or else someone will drop one off that doesn't work, and you will be blamed for it.

You should be able to just switch the power off for a minute. Unplug the power.
Make sure the ribbon is plugged correctly.
Plug it back in and power it on. It should be fine.

If not, you may have fried the wifi/bt module. Try and turn it on without the ribbon in.

Or maybe it is a fuse, and in that case:

Take some high resolution pics of the area. Get out your multimeter, and wait for @Mr.Dutch (aka Mr. Fuse)

[urbananonymous]

Originally Posted by playerkp420 You should be turning them on, checking firmware, and making sure they work. At least I do, before everyone I do. Or else someone will drop one off that doesn't work, and you will be blamed for it. You should be able to just switch the power off for a minute. Unplug the power. Make sure the ribbon is plugged correctly. Plug it back in and power it on. It should be fine. If not, you may have fried the wifi/bt module. Try and turn it on without the ribbon in. Or maybe it is a fuse, and in that case: Take some high resolution pics of the area. Get out your multimeter, and wait for @Mr.Dutch (aka Mr. Fuse)

yeah i did all of the above with no luck... so i guesse ill just wait for @Mr.Dutch ... hey do you have a iptorrents account? if not pm me your e-mail and ill send you a invite. i have a couple invites piled up from uploadin g so much...

[playerkp420]

Originally Posted by urbananonymous yeah i did all of the above with no luck... so i guesse ill just wait for Mr.Dutch ... hey do you have a iptorrents account? if not pm me your e-mail and ill send you a invite. i have a couple invites piled up from uploadin g so much...

No I don't have iptorrents account. I got some extra BitSoup if you want to trade.

[BwE]

Protip: It wont YLOD from unplugging ANYTHING while the console is still running. The worst it could do is just POWER OFF or even power ON if its in standby.

[stdule]

Check fuse-F6001,TH3701,TH3702

[urbananonymous]

Originally Posted by playerkp420 No I don't have iptorrents account. I got some extra BitSoup if you want to trade.

pm me your email, ill send you the iptorrents invite

what should there voltage be?

[stdule]

Fuse F6001=12V,TH3701=5V,TH3702=3,3V

[stdule]

Originally Posted by urbananonymous pm me your email, ill send you the iptorrents invite what should there voltage be?

Fuse F6001=12V,TH3701=5V,TH3702=3,3V .If the fuse F6001 damaged then get a ps3 with YLOD failure.

[Mr.Dutch]

Originally Posted by stdule Check fuse-F6001,TH3701,TH3702

Damn you, i'm Mr.Fuse, not you.

too bad that you are right about the fuse, it's listed as a 5A fuse, so how easily would it blow...